DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:C1A40

DTC Code DTC Name
C1A40 ENG / EHV Device

DESCRIPTION

When the driving support ECU receives a hybrid control system or SFI system malfunction signal from the power management control ECU or ECM via the CAN communication line, DTC C1A40 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A40 While power switch is on (IG), hybrid control system or SFI system malfunction signal is detected for 1 second

  • Hybrid control system

  • Power management control ECU

  • SFI system

  • ECM

  • Driving support ECU

WIRING DIAGRAM

A01NDL1E15

INSPECTION PROCEDURE

PROCEDURE


  1. READ OUTPUT DTC (HYBRID CONTROL SYSTEM)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Hybrid Control / DTC.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO HYBRID CONTROL SYSTEM Click here

    A

  2. READ OUTPUT DTC (SFI SYSTEM)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / DTC.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO SFI SYSTEM Click here

    A

  3. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A40)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 40 km/h (25 mph) or more.

      2. Turn the cruise control main switch on.

      3. Push the -SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A40 is output B

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  4. REPLACE POWER MANAGEMENT CONTROL ECU


    1. Replace the power management control ECU Click here for LHD, Click here for RHD).


    NEXT

  5. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A40)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 40 km/h (25 mph) or more.

      2. Turn the cruise control main switch on.

      3. Push the -SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A40 is output B

    B

    REPLACE ECM Click here

    A

    END

  6. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  7. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A40)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 40 km/h (25 mph) or more.

      2. Turn the cruise control main switch on.

      3. Push the -SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A40 is output B

    B

    REPLACE DRIVING SUPPORT ECU Click here

    A

    END