HYBRID CONTROL SYSTEM, Diagnostic DTC:P0516-769, P0517-770

DESCRIPTION

• The thermistor assembly (battery temperature sensor) detects the auxiliary battery temperature. The resistance of the thermistor assembly built into the thermistor changes in accordance with changes in the auxiliary battery temperature. The lower the auxiliary battery temperature, the higher the thermistor assembly resistance. Conversely, the higher the temperature, the lower the resistance. The thermistor is connected to the power management control ECU (HV CPU). A voltage of 5 V is supplied to the thermistor assembly from the THB terminal of the power management control ECU (HV CPU) through its internal resistor R. This means that resistor R and the thermistor assembly are connected in series. The voltage at the THB terminal and the resistance value change in accordance with changes in the auxiliary battery temperature. Based on this signal, the power management control ECU (HV CPU) reduces the charging current when the auxiliary battery temperature is high to protect the auxiliary battery.

  

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

   
   

   1. Check the connections of the power management control ECU connectors.

      

      Text in Illustration

      *1

      for LHD

      *2

      for RHD

      OK
      The connectors are connected securely and there are no contact problems.

   
   

   NG

   CONNECT SECURELY

   OK

2. READ VALUE USING INTELLIGENT TESTER (AUXILIARY BATT TEMPERATURE)

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

   4. Read the Data List.

      Result
      Result Proceed to -40°C (-40°F) A 215°C (419°F) B Same as actual temperature C

   5. Turn the power switch off.

   
   

   B

   READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT) Click here

   C

   CHECK FOR INTERMITTENT PROBLEMS Click here

   A

3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)

   
   

   1. 

      Disconnect connector P61 from the thermistor assembly.

   2. 

      Connect terminals 2 (THB) and 1 (E2) of vehicle side connector P61 of the thermistor assembly.

   3. Connect the intelligent tester to the DLC3.

   4. Turn the power switch on (IG).

   5. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

   6. Read the Data List.

      OK
      Tester Display Condition Specified Condition Auxiliary Batt Temperature Terminals THB and E2 connected. Power switch on (IG) 215°C (419°F)

      Text in Illustration

      *1	Front view of wire harness connector (to Thermistor Assembly)

   7. Turn the power switch off.

   8. Connect the thermistor assembly connector.

   
   

   NG

   CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY) Click here

   OK

   REPLACE THERMISTOR ASSEMBLY

4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)

   
   
   1. 

      Text in Illustration

      *1	Component with harness connected (Power Management Control ECU)

      Connect terminals 28 (THB) and 30 (ETHB) of connector F97 of the power management control ECU.

   2. Connect the intelligent tester to the DLC3.

   3. Turn the power switch on (IG).

   4. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

   5. Read the Data List.

      OK
      Tester Display Condition Specified Condition Auxiliary Batt Temperature Terminals THB and ETHB connected. Power switch on (IG) 215°C (419°F)

      Result
      Result Proceed to OK A NG (for LHD) B NG (for RHD) C

   6. Turn the power switch off.

   
   

   B

   REPLACE POWER MANAGEMENT CONTROL ECU (for LHD) Click here

   C

   REPLACE POWER MANAGEMENT CONTROL ECU (for RHD) Click here

   A

   REPAIR OR REPLACE HARNESS OR CONNECTOR

5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)

   
   

   1. 

      Disconnect connector P61 from the thermistor assembly.

   2. Connect the intelligent tester to the DLC3.

   3. Turn the power switch on (IG).

   4. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

   5. Read the Data List.

      OK
      Tester Display Condition Specified Condition Auxiliary Batt Temperature Power switch on (IG) -40°C (-40°F)

   6. Turn the power switch off.

   7. Connect the thermistor assembly connector.

   
   

   NG

   CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY) Click here

   OK

   REPLACE THERMISTOR ASSEMBLY

6. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)

   
   

   1. Disconnect connector P61 from the thermistor assembly.

   2. 

      Text in Illustration

      *1	Front view of wire harness connector (to Thermistor Assembly)
      *2	Rear view of wire harness connector (to Power Management Control ECU)

      Disconnect connector F97 from the power management control ECU.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for open)
      Tester Connection Switch Condition Specified Condition F97-28 (THB) - P61-2 (THB) Power switch off Below 1 Ω F97-30 (ETHB) - P61-1 (E2) Power switch off Below 1 Ω

      Standard Resistance (Check for short)
      Tester Connection Switch Condition Specified Condition F97-28 (THB) or P61-2 (THB) - Body ground and other terminals Power switch off 10 kΩ or higher F97-30 (ETHB) or P61-1 (E2) - Body ground and other terminals Power switch off 10 kΩ or higher

      Result
      Result Proceed to OK (for LHD) A OK (for RHD) B NG C

   4. Connect the thermistor assembly connector.

   5. Connect the power management control ECU connector.

   
   

   B

   REPLACE POWER MANAGEMENT CONTROL ECU (for RHD) Click here

   C

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   A

   REPLACE POWER MANAGEMENT CONTROL ECU (for LHD) Click here