STEERING WHEEL INSTALLATION


  1. INSTALL STEERING PAD ATTACHING SCREW


    1. A01NG0M

      Install the 2 steering pad attaching screws to the lower steering wheel boss cover.

  2. INSTALL LOWER STEERING WHEEL BOSS COVER


    1. A01NHG4

      Engage the 2 claws to install the lower steering wheel boss cover to the steering wheel sub-assembly.

    2. Engage the 2 pins.

  3. INSTALL CRUISE CONTROL SWITCH WIRE

  4. INSTALL CRUISE CONTROL MAIN SWITCH


    1. A01NHMS

      Install the cruise control main switch with the 2 screws.

    2. A01NEOD

      Connect the connector.

  5. INSTALL STEERING PAD SWITCH ASSEMBLY


    1. A01NCM3

      Engage the 2 claws and pin to install the steering pad switch assembly (RH side) to the steering wheel sub-assembly.

    2. Install the screw.

      Torque:
      2.4 N*m  { 25 kgf*cm, 21 in.*lbf }
    3. A01NGMB

      Engage the 2 claws and pin to install the steering pad switch assembly (LH side) to the steering wheel sub-assembly.

    4. Install the screw.

      Torque:
      2.4 N*m  { 25 kgf*cm, 21 in.*lbf }

  6. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  7. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01ND9V

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A01NHYYE01
      Text in Illustration
      *1 Alignment Mark

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  8. INSTALL STEERING WHEEL ASSEMBLY


    1. A01NEHSE01
      Text in Illustration
      *1 Matchmark

      Align the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  9. INSTALL STEERING PAD

    Tech Tips

    Refer to the instructions for Installation of the steering pad Click here.

  10. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Make sure that the cable has been disconnected from the battery terminal for at least 2 seconds before reconnecting the cable.

    • Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSPECT STEERING PAD


    1. A01NEKH

      Visually check for defects with the steering pad installed on the vehicle.


      1. The defects are as follows:


        • Cuts on the surface and in the grooves of the steering pad

        • Small cracks on the surface and in the grooves of the steering pad

        • Significant discoloration on the surface and in the grooves of the steering pad

        OK
        No defects are found.

        Tech Tips

        If any of the defects is found, replace the steering pad with a new one.

    2. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  13. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  14. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.