POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM FREEZE FRAME DATA
-
FREEZE FRAME DATA
Note
-
Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
-
Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.
-
Turn the power switch off.
-
Connect the intelligent tester to the DLC3.
-
Turn the power switch on (IG).
-
Turn the intelligent tester on.
-
Check the freeze frame data. Enter the following menus: Chassis / Tilt & Telescopic / DTC.
Tilt & Telescopic Tester Display Measurement Item/Range Normal Condition Diagnostic Note Tilt Position Current tilt position data/
Min.: 0
Max.: 65535
28672 to 36864 - Telesco Position Current telescopic position data/
Min.: 0
Max.: 65535
28672 to 36864 - Tilt Return Position Memorized tilt return position data/
Min.: 0
Max.: 65535
28672 to 36864 - Telesco Return Position Memorized telescopic return position data/
Min.: 0
Max.: 65535
28672 to 36864 - Tilt Up Switch Input state of tilt up by manual switch/
ON or OFF
ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch
- Tilt Up SW(CAN) Input state of tilt up by manual switch/
ON or OFF
ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch
- Tilt Down Switch Input state of tilt down by manual switch/
ON or OFF
ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch
- Tilt Down SW(CAN) Input state of tilt down by manual switch/
ON or OFF
ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch
- Telesco Short Switch Input state of telescopic short by manual switch/
ON or OFF
ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch
- Telesco Short SW(CAN) Input state of telescopic short by manual switch/
ON or OFF
ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch
- Telesco Long Switch Input state of telescopic long by manual switch/
ON or OFF
ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch
- Telesco Long SW(CAN) Input state of telescopic long by manual switch/
ON or OFF
ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch
- T&T Manual SW Data Voltage data of manual switch/
Min.: 0.00 V
Max.: 4.99 V
Neutral position: Below 0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
- Power Source Voltage Voltage data of power supply/
Min.: 0.00 V
Max.: 19.99 V
11 to 14 V - Freeze Speed Info Vehicle speed data/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed - IG Switch (CAN) Communication state of power switch/
ON or OFF
ON: Communication normal
OFF: Communication interrupted
- IG Switch Input state of power switch/
ON or OFF
ON: Input signal normal
OFF: Input signal interrupted
- Receive from Meter Communication state of combination meter signal/
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
- Receive from Seat ECU Communication state of position control ECU signal/
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
- Receive from Combi Communication state of combination switch ECU signal/
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
- J/B Communication state of main body ECU signal/
OK or Interpt
OK: Communication normal
Interpt: Communication interrupted
- Handle Position Steering wheel position signal/
Away or Return
Away: Steering wheel in away position
Return: Steering wheel in return position
(Except remote start)
- The Number of DTCs Number of stored DTCs/
Min.: 0
Max.: 255
Actual number of stored DTCs -
-