PARKING BRAKE PEDAL (for RHD) INSTALLATION


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01NFC0

      Install the parking brake control pedal assembly with the 3 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    2. A01NHCY

      Connect the parking brake switch connector.

    3. A01NCSE

      Insert the No. 1 parking brake cable assembly toward the outside of the cabin.

    4. A01NHEU

      Install the No. 1 parking brake cable assembly with the 2 bolts and 3 nuts.

      Torque:
      Bolt
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Nut
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    5. Install the clamp.

    6. A01NH7FE02
      Text in Illustration
      *1 Lock Nut

      Temporarily install the lock nut.

      Tech Tips

      After adjusting parking brake pedal travel, tighten the lock nut.

  2. INSTALL PARKING BRAKE EQUALIZER


    1. A01NDK8

      Install the parking brake equalizer to the No. 1 parking brake cable assembly as shown in the illustration.

    2. A01NE1H

      Slide the rubber boot back as shown in the illustration.

  3. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A01NCU5

      Connect the No. 3 parking brake cable assembly to the parking brake equalizer.

  4. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tech Tips

    Perform the same procedure as for the No. 3 parking brake cable assembly.

  5. INSTALL REAR ENGINE SERVICE COVER ASSEMBLY


    1. A01NECP

      Install the rear engine service cover assembly with the 2 bolts.

  6. INSTALL CENTER FRONT FLOOR COVER


    1. A01NGBG

      Engage the 3 clips to install the center front floor cover.

    2. A01NFS1

      Install the 7 bolts and 2 screws.

  7. INSTALL REAR NO. 1 AIR DUCT


    1. A01NE08

      Install the rear No. 1 air duct.

    2. Engage the wire harness clamp.

  8. INSTALL REAR NO. 2 AIR DUCT


    1. A01NERU

      Install the rear No. 2 air duct with the clip.

    2. Install the floor carpet.

  9. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01NFZB

      Engage the 2 clips to install the cowl side trim sub-assembly LH.

    2. Install the clip.

  10. INSTALL FRONT DOOR SCUFF PLATE LH


    1. w/ Illumination:


      1. Connect the connector.

    2. A01NHW7

      Engage the 4 clips, guide and 7 claws, and install the front door scuff plate LH.

  11. INSTALL CONSOLE BOX


    1. A01NDV8E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 2 clips.

    4. A01NCM1

      Install the console box with the 5 screws <D>.

  12. INSTALL FRONT CONSOLE BOX COVER


    1. A01NHOI

      Connect the connector.

    2. Engage the 5 guides and 2 clips, and install the front console box cover.

  13. INSTALL INSTRUMENT PANEL FINISH PANEL

    Tech Tips

    This is symmetrical to the LHD model Click here.

  14. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

    Tech Tips

    Refer to the instructions for Installation of the brake pedal support assembly Click here.

  15. INSTALL REAR CONSOLE BOX ASSEMBLY

    Tech Tips

    Refer to the instructions for Installation of the rear console box assembly Click here.

  16. INSTALL FRONT SEAT ASSEMBLY LH

    Tech Tips

    Refer to the instructions for Installation of the front seat assembly Click here.

  17. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL


    1. Remove the No. 1 instrument panel under cover sub-assembly Click here.

    2. Completely release the parking brake pedal.

    3. A01NH7FE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    4. Remove the rear wheels.

    5. Temporarily install the hub nuts to the hub bolts.

      Tech Tips

      Securely install the hub nuts to the rear disc.

    6. Remove the shoe adjusting hole plug.

    7. A01NCOWE04
      Text in Illustration
      *1 Expand
      *2 Contract

      Turn the shoe adjuster and expand the shoe until the disc locks.

    8. Turn and contract the shoe adjuster until the disc can rotate smoothly.

      Standard
      Returns 8 notches.

    9. Check that there is no brake drag against the shoe.

    10. Install the shoe adjusting hole plug.

    11. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
    12. A01NH7FE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    13. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    14. Check that there is no brake drag against the shoe.

    15. Remove the hub nuts from the hub bolts.

    16. Install the rear wheels.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    17. Install the No. 1 instrument panel under cover sub-assembly Click here.

  18. INSPECT BRAKE WARNING LIGHT


    1. When operating the parking brake pedal, check that the brake warning light illuminates.

      Standard
      The brake warning light always illuminates at the first click.