BRAKE PEDAL (for RHD) REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

  2. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  3. REMOVE REAR DECK FLOOR BOX


    1. A01NDSY

      Remove the 3 clips and the rear deck floor box.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01NF7E

      Remove the 2 screws <D>.

    2. A01NHV4

      Disengage the claw and 2 guides as shown in the illustration.

    3. Disconnect each connector.

    4. Disengage each clamp and remove the No. 1 instrument panel under cover sub-assembly.

  8. REMOVE INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  9. REMOVE INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. A01NGJB

      Using moulding remover B, disengage the 6 clips as shown in the illustration.

    2. Disconnect the connector and remove the instrument panel garnish RH.

  10. REMOVE NO. 1 SWITCH HOLE BASE


    1. A01NFNE

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01NGE1

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A01NG78

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  12. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

    CAUTION:

    When storing the driver side knee airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NHD8

      Remove the 4 bolts.

    4. Disengage the 2 claws and 2 hooks to separate the driver side knee airbag assembly.

    5. A01NHO2E01

      Disengage the claw to remove the hood lock control cable.

    6. Using a screwdriver with the tip wrapped with protective tape, disconnect the airbag connector to remove the driver side knee airbag assembly.

      Text in Illustration
      *1 Protective Tape

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  13. REMOVE NO. 4 AIR DUCT SUB-ASSEMBLY


    1. A01NDF8

      Disengage the claw and guide, and remove the No. 4 air duct sub-assembly.

      Note

      Do not damage the claw or guide.

  14. REMOVE STOP LIGHT SWITCH ASSEMBLY


    1. A01NHDH

      Disconnect the connector.

    2. A01NDE7E01
      Text in Illustration
      *1 Lock Nut

      Loosen the stop light switch lock nut and remove the stop light switch assembly.

  15. REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY


    1. A01NDNNE01

      Disconnect the sensor connector.

    2. A01NF0RE01

      Remove the 2 bolts and brake pedal stroke sensor.

      Note

      Do not drop the sensor. If the sensor has been dropped, replace the brake pedal stroke sensor with a new one.

  16. REMOVE BRAKE PEDAL RETURN SPRING


    1. A01NFGS

      Remove the brake pedal return spring from the push rod pin and brake pedal support sub-assembly.

  17. SEPARATE MASTER CYLINDER PUSH ROD CLEVIS


    1. A01NCWH

      Remove the clip and push rod pin, and separate the master cylinder push rod clevis from the brake pedal sub-assembly.

  18. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY


    1. A01NEB7

      Remove the 2 bolts and separate the brake pedal support assembly from the instrument panel reinforcement.

    2. A01NGX4

      Disengage the clamp.

    3. A01NGPC

      Remove the 4 nuts and brake pedal support assembly from the body.