ПЕРЕДНИЙ ПРИВОДНОЙ ВАЛ В СБОРЕ (для моделей с 1ND-TV) ПОВТОРНАЯ СБОРКА


  1. INSTALL FRONT DRIVE SHAFT DUST COVER


    1. A011BEFE01

      Using SST, install a new dust cover into the inboard joint until it is flush with the end.

      SST
      09527-10011

      Note


      • Install the dust cover in the correct orientation.

      • Do not deform the dust cover.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  2. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH


    1. Install a new snap ring.

  3. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH

    Tech Tips

    Use the same procedure for the RH side as for the LH side.

  4. INSTALL FRONT AXLE OUTBOARD JOINT BOOT


    1. Wrap the spline of the outboard joint shaft with protective tape.

    2. Install new parts onto the outboard joint shaft in the following order.

      Installation Order
      Order Part Name
      1. Front No. 2 axle outboard joint boot clamp
      2. Front axle outboard joint boot
      3. Front axle outboard joint boot clamp

    3. Pack the joint portion of the outboard joint shaft and the outboard joint boot with grease.

      Standard Quantity
      135 to 145 g (4.8 to 5.1 oz.)

    4. Install the outboard joint boot onto the outboard joint shaft groove.

      Note

      Keep the groove free of grease.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  5. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

    CAUTION:

    Wear protective gloves to avoid injuries to your hands.


    1. A0117PU

      Install a new boot clamp onto the outboard joint boot and provisionally fold back the lever.

      Note


      • Set the lever into the guide groove correctly and install the clamp as far into the inner side of the vehicle as possible.

      • Check the band and the lever for any deformation before folding back the lever.

    2. A01199LE07
      Text in Illustration
      *1 Weight
      *2 Contact

      Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work plane. Roll the outboard joint and fold the lever until a click sound can be heard.

      Note


      • Do not damage the deflector.

      • Make sure that the outboard joint is in direct contact with the work plane.

    3. A011B74

      Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      Note

      Do not damage the outboard joint boot.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

    CAUTION:

    Wear protective gloves to avoid injuries to your hands.


    1. A0117CF

      Install a new boot clamp onto the outboard joint boot and provisionally fold back the lever.

      Note


      • Set the lever into the guide groove correctly.

      • Check the band and the lever for any deformation before folding back the lever.

    2. A011BKRE01

      Using water pump pliers, pinch the boot clamp to provisionally fix it.

    3. A0118SV

      Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      Note

      Do not damage the outboard joint boot.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  7. INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side)


    1. A0119VOE01

      Install the drive shaft damper onto dimension (A) shown in the illustration.

      Dimension (A)
      398 to 402 mm (15.67 to 15.83 in.)

  8. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side)

    A0117MWE01
    Text in Illustration
    *1 One Touch Type
    *2 Claw Engagement Type

    1. One touch type:


      1. Install the new damper clamp onto the front drive shaft damper and fix the damper clamp with a screwdriver.

    2. Claw engagement type:


      1. Using needle-nose pliers, engage the 2 claws and install the new damper clamp as shown in the illustration.

  9. INSTALL FRONT AXLE INBOARD JOINT GROMMET


    1. A0119P9E02
      Text in Illustration
      *1 Groove

      Install a new inboard joint grommet onto the inboard joint groove.

      Note

      Securely fit the protrusion on the inboard joint grommet into the inboard joint groove.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  10. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY


    1. Install new parts onto the outboard joint shaft in the following order.

      Installation Order
      Order Part Name
      1. Front axle inboard joint boot clamp
      2. Front axle inboard joint boot
      3. Front No. 2 axle inboard joint boot clamp

    2. Fix the outboard joint shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    3. Remove the protective tape.

    4. A011AO0E04
      Text in Illustration
      *1 Matchmark

      Align the matchmarks and install the tripod joint onto the outboard joint shaft.

      Note

      Face the serrated side of the tripod joint outward and install it onto the outboard joint end.

    5. Using a brass bar and hammer, install the tripod joint.

      Note


      • Do not hit the rollers.

      • Keep the tripod joint free of foreign matter.

    6. A011749

      Using a snap ring expander, install a new snap ring.

    7. Pack the inboard joint with grease.

      Standard Quantity
      175 to 185 g (6.2 to 6.5 oz.)
    8. A011ALUE04
      Text in Illustration
      *1 Matchmark

      Align the matchmarks and install the inboard joint onto the outboard joint shaft.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  11. INSTALL FRONT AXLE INBOARD JOINT BOOT


    1. Install the inboard joint boot into the grooves of the inboard joint grommet and outboard joint shaft.

      Note

      Keep the grooves free of grease.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  12. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

    CAUTION:

    Wear protective gloves to avoid injuries to your hands.


    1. A0117CF

      Install a new boot clamp onto the inboard joint boot and provisionally fold back the lever.

      Note


      • Set the lever into the guide groove correctly.

      • Check the band and the lever for any deformation before folding back the lever.

    2. A011BKRE01

      Using water pump pliers, pinch the boot clamp to provisionally fix it.

    3. A0118SV

      Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      Note

      Do not damage the inboard joint boot.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  13. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP


    1. Install the new boot clamp onto the inboard joint boot.

    2. A011AYLE08

      Adjust dimension (A) until the drive shaft is within the specified length.

      Dimension (A)
      LH RH

      565.9 mm

      (22.28 in.)

      845.9 mm

      (33.30 in.)
    3. A0118ISE05
      Text in Illustration
      *1 Boot Clamp
      *2 Inboard Joint Grommet
      *3 Fulcrum Point
      *4 Recessed Part

      While keeping dimension (A) within the specified length, put the inside of the inboard joint under atmospheric pressure by pulling the recessed parts on the inboard joint grommet out.

    4. Set the lever fulcrum point at any point A indicated in the illustration and temporarily bend the lever.

      CAUTION:

      Wear protective gloves to avoid injuries to your hands.

      Note


      • Perform this work with the inside of the inboard joint kept at atmospheric pressure.

      • Set the lever into the guide groove correctly and install the clamp as far into the inner side of the vehicle as possible.

      • Check the band and the lever for any deformation before folding back the lever.

    5. A0119DSE03
      Text in Illustration
      *1 Weight
      *2 Contact

      Lean your weight on your hand and roll the inboard joint forward while pressing the inboard joint against the work plane. Roll the inboard joint and fold the lever until a click sound can be heard.

      Note


      • Do not damage the deflector.

      • Make sure that the inboard joint is in direct contact with the work plane.

    6. A0118J7

      Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      Note

      Do not damage the inboard joint boot.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  14. INSPECT FRONT DRIVE SHAFT ASSEMBLY


    1. A0117WI

      Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.

    2. Check for cracks, damage and grease leakage on the boot joint.

      Note

      Keep the drive shaft level while moving it.

    3. A011AYLE08

      Check dimension (A).

      Dimension (A)
      LH RH

      565.9 mm

      (22.28 in.)

      845.9 mm

      (33.30 in.)