БЛОК МЕХАНИЧЕСКОЙ ТРАНСМИССИИ ПОВТОРНАЯ СБОРКА


  1. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    1. A0119D5E01

      Using SST and a press, install a new front differential case front tapered roller bearing onto the differential case.

      SST
      09309-37010
      09506-35010
    2. A0118RCE01

      Using SST and a press, install the front differential case front tapered roller bearing (outer race) together with the front differential case front plate washer onto the front transaxle case.

      SST
      09950-60020   ( 09951-00680 )
      09950-70010   ( 09951-07200 )

  2. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    1. A0118MGE01

      Using SST and a press, install a new front differential case rear tapered roller bearing onto the differential case.

      SST
      09636-20010
      09726-40010
    2. A011BPFE01
      Text in Illustration
      *1 Front differential case rear tapered roller bearing (outer race)
      *2 Front differential case rear plate washer

      Using SST and a press, install the front differential case rear tapered roller bearing (outer race) together with the front differential case rear plate washer onto the manual transmission case.

      SST
      09950-60020   ( 09951-00730 )
      09950-70010   ( 09951-07100 )

      Tech Tips

      Use a plate washer of the same thickness as the removed one.

  3. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD


    1. A011BM2

      Coat the differential case assembly with gear oil and install it onto the front transaxle case.

    2. A011ABF

      Install the manual transmission case with the 16 bolts.

      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }
    3. A0118W4E01
      Text in Illustration
      *1 Front differential case rear plate washer

      Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

      SST
      09564-32011

    4. Using SST and a torque wrench, measure the preload.

      SST
      09564-32011
      Preload (at starting)
      New bearing
      1.0 to 1.6 N*m (10 to 17 kgf*cm, 9 to 14 in.*lbf)
      Used bearing
      0.8 to 1.3 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)

      If the preload is out of specification, select a front differential case rear plate washer.

      Plate Washer Thickness
      Mark

      Thickness

      mm (in.)

      		 Mark

      Thickness

      mm (in.)
      10 2.100 (0.0827) 26 2.500 (0.0984)
      11 2.125 (0.0837) 27 2.525 (0.0994)
      12 2.150 (0.0846) 28 2.550 (0.1004)
      13 2.175 (0.0856) 29 2.575 (0.1014)
      14 2.200 (0.0866) 30 2.600 (0.1024)
      15 2.225 (0.0876) 31 2.625 (0.1033)
      16 2.250 (0.0886) 32 2.650 (0.1043)
      17 2.275 (0.0896) 33 2.675 (0.1053)
      18 2.300 (0.0906) 34 2.700 (0.1063)
      19 2.325 (0.0915) 35 2.725 (0.1073)
      20 2.350 (0.0925) 36 2.750 (0.1083)
      21 2.375 (0.0935) 37 2.775 (0.1093)
      22 2.400 (0.0945) 38 2.800 (0.1102)
      23 2.425 (0.0955) 39 2.825 (0.1112)
      24 2.450 (0.0965) 40 2.850 (0.1122)
      25 2.475 (0.0974) - -

      Tech Tips


      • Select a thicker plate washer to increase the preload; a thinner plate washer to decrease the preload.

      • Underlines are stamped to distinguish between marks "6" and "9".

      • Make a memo as the torque values will be needed for Output Shaft Bearing Preload.

    5. Remove the 16 bolts and the manual transmission case.

    6. Remove the differential case assembly from the front transaxle case.

  4. INSTALL OUTPUT SHAFT COVER


    1. A0116YW

      Install the output shaft cover onto the front transaxle case.

      Note

      Insert the output shaft cover key into the case groove.

  5. INSTALL FRONT OUTPUT SHAFT BEARING


    1. A0118EDE01
      Text in Illustration
      *1 Front output shaft bearing (outer race)
      *2 Output shaft cover

      Using SST and a press, install the front output shaft bearing (outer race) onto the front transaxle case.

      SST
      09950-60010   ( 09951-00630 )
      09950-70010   ( 09951-07100 )

  6. INSTALL REAR OUTPUT SHAFT BEARING


    1. A011AENE01
      Text in Illustration
      *1 Rear output shaft bearing (outer race)
      *2 Rear output shaft bearing shim

      Using SST and a press, install the rear output shaft bearing (outer race) with the rear output shaft bearing shim onto the manual transmission case.

      SST
      09950-60010   ( 09951-00590 )
      09950-70010   ( 09951-07200 )

  7. ADJUST OUTPUT SHAFT BEARING PRELOAD


    1. A011BM2

      Coat the differential case assembly with gear oil and install it onto the front transaxle case.

    2. A0118SK

      Coat the output shaft assembly with gear oil and install it onto the front transaxle case.

    3. A011ABF

      Install the manual transmission case with the 16 bolts.

      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }
    4. A011AAVE01
      Text in Illustration
      *1 Rear output shaft bearing shim

      Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

      SST
      09564-32011

    5. Using SST and a torque wrench, measure the preload. Calculate the rear output shaft bearing shim value using the following formula.

      SST
      09564-32011
      Formula
      (Differential side bearing preload + Output shaft bearing preload) - Differential side bearing preload = Output shaft bearing preload
      Preload (at starting)
      New Bearing
      Final Gear Combination Differential Ratio Specified Condition
      71/19 3.736

      3.8 to 6.5 N*m

      (39 to 67 kgf*cm, 34 to 58 in.*lbf)
      Used Bearing
      Final Gear Combination Differential Ratio Specified Condition
      71/19 3.736

      2.5 to 4.2 N*m

      (25 to 43 kgf*cm, 22 to 37 in.*lbf)

      If the preload is out of specification, select a rear output shaft bearing shim.

      Plate Washer Thickness
      Mark

      Thickness

      mm (in.)

      		 Mark

      Thickness

      mm (in.)
      50 1.750 (0.0689) 72 2.300 (0.0906)
      51 1.775 (0.0699) 73 2.325 (0.0915)
      52 1.800 (0.0709) 74 2.350 (0.0925)
      53 1.825 (0.0719) 75 2.375 (0.0935)
      54 1.850 (0.0728) 76 2.400 (0.0945)
      55 1.875 (0.0738) 77 2.425 (0.0955)
      56 1.900 (0.0748) 78 2.450 (0.0965)
      57 1.925 (0.0758) 79 2.475 (0.0974)
      58 1.950 (0.0768) 80 2.500 (0.0984)
      59 1.975 (0.0778) 81 2.525 (0.0994)
      60 2.000 (0.0787) 82 2.550 (0.1004)
      61 2.025 (0.0797) 83 2.575 (0.1014)
      62 2.050 (0.0807) 84 2.600 (0.1024)
      63 2.075 (0.0817) 85 2.625 (0.1033)
      64 2.100 (0.0827) 86 2.650 (0.1043)
      65 2.125 (0.0837) 87 2.675 (0.1053)
      66 2.150 (0.0846) 88 2.700 (0.1063)
      67 2.175 (0.0856) 89 2.725 (0.1073)
      68 2.200 (0.0866) 90 2.750 (0.1083)
      69 2.225 (0.0876) 91 2.775 (0.1093)
      70 2.250 (0.0886) 92 2.800 (0.1102)
      71 2.275 (0.0896) - -

      Tech Tips


      • Select a thicker plate washer to increase the preload; a thinner plate washer to decrease the preload.

      • Underlines are stamped to distinguish between marks "6" and "9".

    6. Remove the 16 bolts and the manual transmission case.

    7. Remove the output shaft assembly from the front transaxle case.

    8. Remove the differential case assembly from the front transaxle case.

  8. INSTALL BREATHER PLUG


    1. A011B7KE01

      Using SST and a hammer, install the breather plug onto the manual transmission case.

      SST
      09350-30020   ( 09350-07110 )

  9. INSTALL OUTER SHIFT LEVER OIL SEAL


    1. A0116ZOE02
      Text in Illustration
      *a Drive in depth

      Using SST and a hammer, install a new outer shift lever oil seal onto the manual transmission case.

      SST
      09950-60010   ( 09951-00260 )
      09950-70010   ( 09951-07100 )
      Standard depth
      0.5 to 1.0 mm (0.0197 to 0.0394 in.)

    2. Coat the lip of the outer shift lever oil seal with MP grease.

  10. INSTALL OUTER NO. 1 SHIFT LEVER


    1. A011AY9E02
      Text in Illustration
      *1 Inner slotted spring pin
      *a Drive in depth

      Install the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever onto the manual transmission case.

      Standard depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Tech Tips

      Install the lever with its mark facing outside of the manual transmission case.

    2. Using a pin punch 5 mm and a hammer, install the inner shift lever slotted spring pin onto the inner No. 1 shift lever.

  11. INSTALL NO. 2 TRANSMISSION OIL SEPARATOR


    1. A011901

      Install the No. 2 transmission oil separator with the 2 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  12. INSTALL MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY


    1. A011AWY

      Install the manual transmission oil separator sub-assembly onto the manual transmission case with the bolt.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

      Tech Tips

      Make sure that the end tabs of the manual transmission oil separator sub-assembly are inserted in the grooves of the manual transmission case.

  13. INSTALL NO. 1 TRANSMISSION OIL SEPARATOR


    1. A0118VK

      Install the No. 1 transmission oil separator onto the manual transmission case with the 2 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

      Tech Tips

      Make sure that the tip of the transmission oil separator is inserted in the groove of the transmission case.

  14. INSTALL NO. 1 OIL RECEIVER PIPE


    1. A0118PK

      Install the No. 1 oil receiver pipe onto the manual transmission case.

      Tech Tips

      Make sure that the No. 1 oil receiver pipe fully contacts the manual transmission case.

  15. INSTALL STRAIGHT PIN


    1. A0117NBE02
      Text in Illustration
      *a Protrusion height

      Using a plastic-faced hammer, tap in 4 new straight pins to the specified protrusion height.

      Protrusion height
      8.5 to 9.5 mm (0.335 to 0.374 in.)

  16. INSTALL REVERSE RESTRICT PIN ASSEMBLY


    1. A011B8E

      Install the reverse restrict pin assembly onto the front transaxle case.

  17. INSTALL TRANSMISSION OIL SEPARATOR


    1. A0119ZN

      Install the transmission oil separator onto the front transaxle case with the 3 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  18. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    1. A0119SQE02
      Text in Illustration
      *a Drive in depth

      Using SST and a hammer, install a new front transaxle case oil seal onto the front transaxle case.

      SST
      09950-60010   ( 09951-00360 )
      09950-70010   ( 09951-07150 )
      Standard depth
      0.9 to 1.9 mm (0.0354 to 0.0748 in.)

    2. Coat the lip of the front transaxle case oil seal with MP grease.

  19. INSTALL TRANSMISSION MAGNET


    1. A0118BM

      Clean the transmission magnet and install it onto the front transaxle case.

  20. INSTALL INPUT SHAFT COVER


    1. A0118FF

      Install the input shaft cover onto the manual transmission case.

      Note

      Insert the input shaft cover key into the manual transmission case groove.

  21. INSTALL REAR INPUT SHAFT BEARING SHIM


    1. A0118KUE11
      Text in Illustration
      *1 Manual transmission case
      *2 Input shaft assembly
      *3 Front transaxle case
      *a Dimension A
      *b Dimension B
      *c Dimension C

      Rear input shaft bearing shim should be washed before assembly.

      Note

      Apply grease allowed on shim, (to avoid) falling shim off, from case during assembly.

    2. Measure the area between the end of the manual transmission case and the rear input shaft bearing shim (Dimension A).

    3. Measure the area between the end of the front transaxle case and the installation surface of the front input shaft bearing (Dimension B).

    4. Measure the area between both input shaft bearing outer races (Dimension C).

      Note

      Measure Dimension C with each bearing having no axial clearance.

    5. Calculate the rear input shaft bearing shim value using the following formula.

      Formula
      (Dimension A + Dimension B) - Dimension C - rear input shaft bearing shim thickness = 0.02 to 0.14 mm (0.000788 to 0.00551 in.)

      If the thickness is out of specification, select a rear output shaft bearing shim.

      Rear Input Shaft Bearing Shim Thickness
      Mark

      Thickness

      mm (in.)

      		 Mark

      Thickness

      mm (in.)
      08 1.30 (0.0512) 14 1.60 (0.0630)
      09 1.35 (0.0531) 15 1.65 (0.0650)
      10 1.40 (0.0551) 16 1.70 (0.0669)
      11 1.45 (0.0571) 17 1.75 (0.0689)
      12 1.50 (0.0591) 18 1.80 (0.0709)
      13 1.55 (0.0610) 19 1.85 (0.0728)
    6. A0117AN

      Coat the rear input shaft bearing shim with MP grease and install it onto the manual transmission case.

      Note

      Do not apply MP grease to the oil grooves.

  22. INSTALL DIFFERENTIAL CASE ASSEMBLY


    1. A011BM2

      Coat the differential case tapered roller bearing with gear oil and install the differential case assembly onto the front transaxle case.

  23. INSTALL INPUT SHAFT ASSEMBLY


    1. Apply gear oil to all sliding and rotating parts.

    2. A01199DE01
      Text in Illustration
      *1 No. 1 gear shift fork shaft
      *2 Output shaft assembly

      Coat the No. 1 gear shift fork shaft with gear oil and install it.

    3. A011AMSE02
      Text in Illustration
      *1 No. 2 gear shift fork shaft
      *2 No. 3 gear shift fork shaft
      *3 Input shaft assembly

      Coat the No. 2 gear shift fork shaft and No. 3 gear shift fork shaft with gear oil and install them.

    4. Provisionally install the output shaft, input shaft and 3 gear shift fork shafts, and tie them with a rope or string.

    5. A011BFN

      Install the input shaft assembly, output shaft assembly and 3 gear shift fork shaft assemblies from the front transaxle case.

  24. INSTALL OUTER SELECT LEVER OIL SEAL


    1. A0119A2E02
      Text in Illustration
      *a Drive in depth

      Using SST and a hammer, install a new outer select lever oil seal onto the front transaxle case.

      SST
      09950-60010   ( 09951-00240 )
      09950-70010   ( 09951-07100 )
      Standard depth
      0.5 to 1.0 mm (0.0197 to 0.0394 in.)

    2. Coat the lip of the outer select lever oil seal with MP grease.

  25. INSTALL OUTER SELECT LEVER


    1. A011AP4E01
      Text in Illustration
      *1 Inner select lever
      *2 Outer select lever

      Install the outer select lever and inner select lever onto the front transaxle case.

      Tech Tips

      Install the lever with its mark positioned outside of the front transaxle case.

    2. A0117MT

      Coat the threads of the select inner select lever set bolt with sealant and install them using a socket hexagon 6 mm.

      Sealant
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  26. INSTALL SHIFT INTER LOCK PLATE


    1. A0118RT

      Install the shift inter lock plate.

  27. INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY


    1. A0118EK

      Turn the shift and select lever shaft assembly and inner select lever counterclockwise and install them to the front transaxle case.

      Tech Tips

      When installing the inner select lever, make sure to engage it with the shift inter lock plate.

  28. INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY


    1. A0118JF

      Install the reverse shift arm bracket assembly onto the front transaxle case with the 2 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  29. INSTALL REVERSE SHIFT FORK SHAFT ASSEMBLY


    1. A01197V

      Coat the reverse shift fork shaft assembly with gear oil and install it.

  30. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY


    1. A0116YKE02
      Text in Illustration
      *a Parallel

      Coat the reverse idler gear sub-assembly, thrust washer and reverse idler gear shaft with gear oil, and install them as shown in the illustration.

      Note

      Make sure that the reverse idler gear shaft bolt installation surface of the reverse idler gear is parallel to the screw hole on the front transaxle case.

      Tech Tips

      Raise the edge of the reverse shift arm bracket assembly and install the reverse shift arm bracket assembly to the reverse shift fork shaft assembly.

  31. INSTALL MANUAL TRANSMISSION CASE


    1. A0118R1E02
      Text in Illustration
      *a

      Seal Packing

      (Seal Diameter 1.2 mm (0.0472 in.))

      Apply FIPG to the manual transmission case as shown in the illustration.

      FIPG
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

      Note


      • Remove any oil from the contact surfaces.

      • Assemble the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

    2. A011BJX

      Push the outer No. 1 shift lever and install the manual transmission case.

      Tech Tips

      Pushing on the outer No. 1 shift lever allows the manual transmission case to be installed.

    3. A01190K

      Pull the outer No. 1 shift lever out and turn it clockwise.

    4. A011ABF

      Install the 16 bolts onto the manual transmission case.

      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }

  32. INSTALL OUTER SHIFT LEVER E RING


    1. A011B4U

      Install the outer shift lever E ring onto the outer No. 1 shift lever.

  33. INSTALL TRANSMISSION CASE OIL SEAL

    A011AXCE01
    Text in Illustration
    *1 Installation depth

    1. Coat the lip of a new oil seal with MP grease.

    2. Using SST and a hammer, install the transmission case oil seal.

      SST
      09316-60011   ( 09316-00011 )
      Installation depth
      10.6 to 11.6 mm (0.417 to 0.457 in.)

      Note

      Do not damage the oil seal lip.

  34. INSTALL TRANSAXLE CASE OIL SEAL

    A011ADME01
    Text in Illustration
    *1 Installation depth

    1. Coat the lip of a new oil seal with MP grease.

    2. Using SST and a hammer, install the transaxle case oil seal.

      SST
      09630-24014   ( 09620-24051 )
      09950-60010   ( 09951-00410, 09951-00520, 09952-06010 )
      09950-70010   ( 09951-07100 )
      Installation depth
      1.4 to 2.4 mm (0.055 to 0.094 in.)

      Note

      Do not damage the oil seal lip.

  35. INSTALL SHIFT DETENT BALL


    1. A011ATEE02
      Text in Illustration
      *1 Sealant

      Install the 2 shift detent balls and 2 shift detent ball compression springs onto the manual transmission case.

    2. Coat the threads of the 2 shift detent ball plugs with sealant and install them using a socket hexagon 6 mm.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }
    3. A0118EGE01
      Text in Illustration
      *1 Sealant

      Install the shift detent ball and shift detent ball compression spring onto the manual transmission case.

    4. Coat the threads of the shift detent ball plug with sealant and install it using a socket hexagon 6 mm.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

  36. INSTALL LOCK BALL PIN


    1. A0117DCE01
      Text in Illustration
      *1 Sealant

      Install the lock ball pin and compression spring onto the manual transmission case.

    2. Coat the threads of the shift detent ball plug with sealant and install it using a socket hexagon 10 mm.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }

      Note

      Be careful not to drop the ball pin into the manual transmission case.

  37. INSTALL REVERSE IDLER GEAR SHAFT BOLT


    1. A011AD4E01
      Text in Illustration
      *1 Sealant

      Coat the reverse idler gear shaft bolt with sealant and install it with a new gasket.

      Sealant
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

  38. INSTALL NO. 1 LOCK BALL ASSEMBLY


    1. A0117MI

      Coat the threads of the No. 1 lock ball assembly with sealant and install it onto the manual transmission case.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }

  39. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. A011AHG

      Using a 27 mm deep socket wrench, install the park/neutral position switch assembly and a new gasket onto the manual transmission case.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  40. INSTALL TRANSMISSION CASE PLUG


    1. A0118US

      Install the transmission case plug onto the manual transmission case with a new gasket.

      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  41. INSTALL NO. 1 TRANSMISSION CASE PLUG


    1. Using a 30 mm socket wrench, install the No. 1 transmission case plug.

      Torque:
      65 N*m  { 663 kgf*cm, 48 ft.*lbf }

  42. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY


    1. Clean and degrease all installation surfaces for the clutch release with bearing cylinder assembly.

    2. A011BBX

      Temporarily tighten the bleeder clutch release tube onto the clutch release with bearing cylinder assembly.

    3. A0119WU

      Install the new clutch release with the bearing cylinder assembly with 3 new bolts.

      Note


      • The clutch release with bearing cylinder assembly and installation bolts cannot be reused and must be replaced with new ones.

      • Clean and degrease all installation surfaces and make sure the clutch release with bearing cylinder assembly fits securely with the transaxle during installation. The first bolt should be tightened by hand the clutch release with bearing cylinder assembly.

      • Ensure that none of the clutch disc spline grease adheres to the clutch release with bearing cylinder assembly.

      • The clutch release with bearing cylinder assembly cannot be disassembled.

      Torque:
      23 N*m  { 229 kgf*cm, 17 ft.*lbf }

    4. Install the clutch tube boot onto the transaxle.

    5. Install the release cylinder bleeder plug onto the clutch release bleeder.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

    6. Install the release cylinder bleeder plug cap.

    7. A0119X3E01
      Text in Illustration
      *1 Bleeder clutch release tube
      *2 Clutch release bleeder

      Temporarily tighten the bleeder clutch release tube onto the clutch release bleeder.

    8. Temporarily tighten the 2 bolts and install the clutch release bleeder.

    9. A011B1Q

      Using a union nut wrench 10 mm, install the bleeder clutch release tube onto the clutch release with bearing cylinder assembly.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations when union nut wrench is combined with a torque wrench Click here.

  43. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    A0119X3

    1. Separate the bleeder clutch release tube from the clutch release bleeder.

    2. Remove the 2 bolts and the clutch release bleeder.

  44. INSPECT CLUTCH PIPE LINE

    A0119YKE01

    1. Using SST, apply pressure of 0.1 MPa to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

      SST
      09992-00242

      If the pressure drops, replace the bleeder clutch release tube.

  45. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    A0119X3E01
    Text in Illustration
    *1 Bleeder clutch release tube
    *2 Clutch release bleeder

    1. Temporarily tighten the bleeder clutch release tube onto the clutch release bleeder.

    2. Install the 2 bolts and clutch release bleeder.

      Torque:
      17 N*m  { 170 kgf*cm, 12 ft.*lbf }

    3. Using a union nut wrench 10 mm, install the bleeder clutch release tube.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations when union nut wrench is combined with a torque wrench Click here.

  46. INSTALL NO. 1 CLUTCH HOUSING COVER

    A01182D

    1. Install the No. 1 clutch housing cover onto the transaxle.

  47. INSTALL WIRE HARNESS CLAMP BRACKET


    1. A011A1R

      Install the wire harness clamp bracket to the front transaxle case with the bolt.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }
    2. A01187V

      Install the wire harness clamp bracket to the manual transmission case with the bolt.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

  48. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


    1. A0119D6E01

      Using SST, install the back-up light switch and a new gasket onto the manual transmission case.

      SST
      09817-16011
      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }
    2. A011ASV

      Engage the wire harness clamp of the back-up light switch assembly to the wire harness clamp bracket.

  49. INSTALL MANUAL TRANSMISSION FILLER PLUG


    1. A011AAJ

      Install the manual transmission filler plug onto the manual transmission case with a new gasket.

      Torque:
      39 N*m  { 400 kgf*cm, 29 ft.*lbf }

  50. INSTALL MANUAL TRANSMISSION DRAIN PLUG


    1. A0119GI

      Using a socket hexagon 10 mm, install the manual transmission drain plug onto the front transaxle case with a new gasket.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }