МАСЛО И МАСЛЯНЫЙ ФИЛЬТР ЗАМЕНА

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the loss of natural oil from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

  • In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil drain plug and drain the oil into a container.

    3. Clean the oil drain plug.

    4. Install the oil drain plug with a new gasket.

      Torque:
      38 N*m  { 387 kgf*cm, 28 ft.*lbf }

  2. REMOVE OIL FILTER WITH ELEMENT CAP ASSEMBLY

    A0117ALE01
    Text in Illustration
    *1 Clip

    1. Using SST, remove the oil filter with the element cap.

      SST
      09228-06501

      Tech Tips

      As the cap is loosened, when the clip on the cap is facing down or up, oil will spill out of the cap.

  3. REMOVE OIL FILTER ELEMENT

    A011AASE03
    Text in Illustration
    *1 Oil Filter Element
    *2 O-ring

    1. Remove the oil filter element and O-ring from the oil filter cap.

  4. INSTALL OIL FILTER ELEMENT

    A011AASE04
    Text in Illustration
    *1 Oil Filter Element
    *2 O-ring

    1. Clean the inside of oil filter cap, threads, and O-ring groove.

    2. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

    3. Install a new oil filter element into the oil filter cap.

    4. Remove any dirt or foreign matter from the contact surfaces of the oil filter cap (with oil filter element) and oil filter bracket.

    5. Install the oil filter cap (with oil filter element) to the oil filter bracket.

  5. INSTALL OIL FILTER WITH ELEMENT CAP ASSEMBLY

    A011780E01

    1. Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  6. ADD ENGINE OIL


    1. Add clean engine oil and install the oil filler cap.

      Engine Oil
      Engine Oil Grade Oil Viscosity (SAE)
      w/o DPF

      ACEA C2, B1, API CF-4 or CF

      (You may also use API CE or CD)

      • 0W-30

      • 5W-30

      • 10W-30

      • 15W-40

      • 20W-50
      w/ DPF ACEA C2

      • 0W-30

      • 5W-30
      Capacity
      Item Capacity
      Drain and refill with oil filter change 4.0 liters (4.2 US qts, 3.5 Imp. qts)
      Drain and refill with out oil filter change 3.6 liters (3.8 US qts, 3.2 Imp. qts)
      Dry fill 4.8 liters (5.1 US qts, 4.2 Imp. qts)

  7. CHECK ENGINE OIL LEVEL


    1. Warm up and stop the engine, wait for 5 minutes, and check that the oil level is between the Low and Full marks on the dipstick.

      Tech Tips

      If the oil level is low, check for leaks and add oil to the Full mark.

      Note

      Do not add oil above the Full mark.

    2. Warm up the engine until the coolant temperature is 75°C to 86°C (167°F to 187°F), and confirm that the oil maintenance indicator illuminates when driving the vehicle at 15 km/h (9 mph) or more with an engine speed of 1400 to 2600 rpm.

      Tech Tips


      • If the oil maintenance warning indicator illuminates during confirmation driving after an oil change, check for an open or close in the engine oil level sensor Click here. If there is a malfunction, replace the engine oil level sensor Click here.

      • If the oil maintenance warning indicator illuminates, the engine oil level is correct, and the sensor is functioning normally, then check the wire harness and connectors between the engine oil level sensor and engine control ECM Click here.

  8. INSPECT FOR OIL LEAK


    1. Start the engine. Check for engine oil leaks from the connected parts of the oil filter cap and oil filter drain plug.