СИСТЕМА SFI РЕЖИМЫ DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the tester on.

    6. Enter the following menus: Powertrain / Engine and ECT / Data List.

    7. Check the values by referring to the table below.

    Tech Tips

    If no idling conditions are specified, the transmission gear should be in the neutral position, and the A/C switch and all accessory switches should be off.

    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    Vehicle Speed

    Vehicle speed:

    Min.: 0 km/h, Max.: 255 km/h

    Actual vehicle speed Speed indicated on speedometer
    Engine Speed

    Engine speed:

    Min.: 0 rpm, Max.: 16383 rpm

    730 to 830 rpm: Idling*1

    650 to 750 rpm: Idling (shift lever in N or P)*2

    -
    Calculate Load

    Calculated load by ECM:

    Min.: 0%, Max.: 100%


    • 12 to 22%: Idling

    • 10 to 20%: Running without load at 2000 rpm

    -
    Atmosphere Pressure

    Atmospheric pressure:

    Min.: 0 kPa, Max.: 255 kPa

    Approximately 100 kPa: Ignition switch ON -
    MAP

    Intake manifold pressure:

    Min.: 0 kPa, Max.: 255 kPa


    • 80 to 110 kPa: Ignition switch ON

    • 28 to 48 kPa: Idling

    -
    Coolant Temp

    Engine coolant temperature:

    Min.: -40°C, Max.: 140°C

    80 to 102°C

    (176 to 216°F): After warming up


    • If -40°C (-40°F): sensor circuit open


    • If 140°C (284°F): sensor circuit shorted

    Intake Air

    Intake air temperature:

    Min.: -40°C, Max.: 140°C

    Equivalent to ambient air temperature: Ignition Switch ON
    • If -40°C (-40°F): sensor circuit open


    • If 140°C (284°F): sensor circuit shorted

    Ambient temperature

    Ambient temperature:

    Min.: -40°C, Max.: 215°C

    Equivalent to ambient air temperature -
    Engine Run Time

    Engine run time:

    Min.: 0 s

    Max.: 65535 s

    Time since engine started -
    Initial Engine Coolant Temp

    Engine coolant temperature at engine start:

    Min.: -40°C, Max.: 120°C

    Close to ambient air temperature -
    Initial Intake Air Temp

    Intake air temperature at engine start:

    Min.: -40°C, Max.: 120°C

    Close to ambient air temperature -
    Battery Voltage

    Battery voltage:

    Min.: 0 V, Max.: 65.5 V

    11 to 14 V: Ignition switch ON -
    Accel Sens. No.1 Volt %

    Absolute accelerator pedal position No. 1:

    Min.: 0%, Max.: 100%

    10 to 22%: Accelerator pedal released

    52 to 90%: Accelerator pedal fully depressed

    Read value with ignition switch ON (Do not start engine)
    Accel Sens. No.2 Volt %

    Absolute accelerator pedal position No. 2:

    Min.: 0%, Max.: 100%

    24 to 40%: Accelerator pedal released

    68 to 100%: Accelerator pedal fully depressed

    Read value with ignition switch ON (Do not start engine)
    Accel Sensor Out No.1

    Accelerator pedal position sensor No. 1 voltage:

    Min.: 0 V, Max.: 4.98 V

    - -
    Accel Sensor Out No.2

    Accelerator pedal position sensor No. 2 voltage:

    Min.: 0 V, Max.: 4.98 V

    - -
    Accel Sensor Out No.1

    Accelerator pedal position sensor No. 1 voltage:

    Min.: 0 V, Max.: 5 V

    0.5 to 1.1 V: Accelerator pedal released

    2.5 to 4.5 V: Accelerator pedal fully depressed

    Read value with ignition switch ON (Do not start engine)
    Accel Sensor Out No.2

    Accelerator pedal position sensor No. 2 voltage:

    Min.: 0 V, Max.: 5 V

    1.2 to 2.0 V: Accelerator pedal released

    3.4 to 5.0 V: Accelerator pedal fully depressed

    Read value with ignition switch ON (Do not start engine)
    Accelerator Idle Position

    Whether or not accelerator pedal position sensor detecting idle:

    ON or OFF

    ON: Idling -
    Accel Fully Close #1 (AD)

    Accelerator pedal position sensor No. 1 voltage (AD):

    Min.: 0 V, Max.: 4.9804 V

    - ETCS service data
    Accel Fully Close Learn #1

    Accelerator fully closed learning value No. 1:

    Min.: 0 deg, Max.: 124.512 deg

    - ETCS service data
    Accel Fully Close Learn #2

    Accelerator fully closed learning value No. 2:

    Min.: 0 deg, Max.: 124.512 deg

    - ETCS service data
    Throttle Sensor Volt %

    Throttle valve opening percentage according to throttle position sensor:

    Min.: 0%, Max.: 100%


    • 10 to 22%: Accelerator pedal released

    • 64 to 96%: Accelerator pedal fully depressed

    Value calculated based on the voltage at terminal VTA1
    Throttle Sensor #2 Volt %

    Throttle valve opening percentage according to throttle position sensor No. 2:

    Min.: 0%, Max.: 100%


    • 42 to 62%: Accelerator pedal released


    • 92 to 100%: Accelerator pedal fully depressed

    Value calculated based on the voltage at terminal VTA2
    ST1

    Brake pedal signal:

    ON or OFF

    ON: Brake pedal depressed -
    System Guard

    System guard:

    ON or OFF

    - ETCS service data
    Open Side Malfunction

    Throttle valve open side malfunction:

    ON or OFF

    - ETCS service data
    Throttle Idle Position

    Whether or not throttle position sensor detecting idle:

    ON or OFF


    • ON: Accelerator pedal released


    • OFF: Accelerator pedal fully depressed

    -
    Throttle Require Position

    Required throttle position:

    Min.: 0 V, Max.: 5 V

    0.5 to 1.1 V: Idling -

    Throttle Sensor Position

    *3

    Throttle position sensor:

    Min.: 0%, Max.: 100%


    • 0%: Accelerator pedal released


    • 50 to 80%: Accelerator pedal fully depressed

    Recognition value for throttle opening angle on ECM
    Throttle Position No. 1

    Throttle position sensor No. 1 output voltage:

    Min.: 0 V, Max.: 4.98 V

    - -
    Throttle Position No. 2

    Throttle position sensor No. 2 output voltage:

    Min.: 0 V, Max.: 4.98 V

    - -
    Throttle Position No. 1

    Throttle position sensor No. 1 output voltage:

    Min.: 0 V, Max.: 5 V


    • 0.5 to 1.1 V: Accelerator pedal released


    • 3.2 to 4.8 V: Accelerator pedal fully depressed


    • 0.6 to 1.4 V: Fail-safe operating

    -
    Throttle Position No. 2

    Throttle position sensor No. 2 output voltage:

    Min.: 0 V, Max.: 5 V


    • 2.1 to 3.1 V: Accelerator pedal released


    • 4.6 to 5.0 V: Accelerator pedal fully depressed


    • 2.1 to 3.1 V: Fail-safe operating

    -
    Throttle Position Command

    Throttle position command value:

    Min.: 0 V, Max.: 4.9804 V

    0.5 to 4.8 V -
    Throttle Sens Open Pos #1

    Throttle sensor opener position No. 1:

    Min.: 0 V, Max.: 4.9804 V

    0.6 to 1.4 V ETCS service data
    Throttle Sens Open Pos #2

    Throttle sensor opener position No. 2:

    Min.: 0 V, Max.: 4.9804 V

    1.7 to 2.5 V ETCS service data
    Throttle Sens Open #1 (AD)

    Throttle position sensor No. 1 output voltage (AD):

    Min.: 0 V, Max.: 4.9804 V

    0.5 to 4.8 V -
    Throttle Motor

    Whether throttle actuator control permitted:

    ON or OFF


    • ON: Ignition switch ON


    • OFF: ETCS has failed

    -
    Throttle Motor Current

    Throttle actuator current:

    Min.: 0 A, Max.: 20 A

    0 to 3.0 A: Idling ETCS service data
    Throttle Motor DUTY

    Throttle actuator:

    Min.: 0%, Max.: 100%

    10 to 22%: Idling after engine warmed up ETCS service data
    Throttle Motor Current

    Throttle actuator current:

    Min.: 0 A, Max.: 19.92 A

    - ETCS service data
    Throttle Motor Open Duty

    Throttle actuator open duty ratio:

    Min.: 0%, Max.: 100%

    - ETCS service data
    Throttle Motor Close Duty

    Throttle actuator closed duty ratio:

    Min.: 0%, Max.: 100%

    - ETCS service data
    Throttle Motor Duty (Open)

    Throttle actuator duty ratio (open):

    Min.: 0%, Max.: 100%

    0 to 40%: Idling ETCS service data
    Throttle Motor Duty (Close)

    Throttle actuator duty ratio (closed):

    Min.: 0%, Max.: 100%

    0 to 40%: Idling ETCS service data
    Throttle Fully Close Learn

    Throttle valve fully closed:

    (learned value):

    Min.: 0 V, Max.: 5 V

    0.4 to 1.0 V: Accelerator pedal released -
    ETCS Actuator Power

    ETCS power supply:

    ON or OFF


    • ON: Ignition switch ON and system normal


    • OFF: ETCS has failed

    -
    +BM Voltage

    +BM voltage:

    Min.: 0 V, Max.: 19.9 V

    11 to 14 V: Ignition switch ON and system normal ETCS service data
    Actuator Power Supply

    Actuator power supply:

    ON or OFF

    ON: Idling ETCS service data
    Clutch Current

    Clutch current:

    Min.: 0 A, Max.: 2.49 A

    - ETCS service data
    Fail Safe Drive

    Whether or not fail safe function executed:

    ON or OFF


    • ON: ETCS has failed


    • OFF: ETCS normal

    ETCS service data
    Fail Safe Drive (Main CPU)

    Whether or not fail safe function executed:

    ON or OFF


    • ON: ETCS has failed


    • OFF: ETCS normal

    ETCS service data
    Injector (Port)

    Injection period of No. 1 cylinder:

    Min.: 0 ms, Max.: 32.64 ms

    1.2 to 2.0 ms: Idling, engine warmed up -
    Injection Volume (Cylinder 1)

    Injection volume (Cylinder 1):

    Min.: 0 ml, Max.: 2.048 ml

    0 to 0.15 ml: Idling Total fuel injection volume of 10 injections
    Fuel Pump/Speed Status

    Fuel pump status:

    ON or OFF

    ON: Engine running Active Test support data
    EVAP (Purge) VSV

    Purge VSV control duty:

    Min.: 0%, Max.: 100%

    10 to 50%: Idling Order signal from ECM
    Evap Purge Flow

    Ratio of evaporative purge flow to intake air volume:

    Min.: 0%, Max.: 102.4%

    0 to 4%: racing at 2000 rpm, engine warmed up -
    Purge Density Learn Value

    Learning value of purge density:

    Min.: -50, Max.: 350

    -40 to 10: Idling -
    EVAP Purge VSV

    Purge VSV status:

    ON or OFF

    - Active Test support data
    Target Air-Fuel Ratio

    Ratio compared to stoichiometric level:

    Min.: 0, Max.: 1.999

    0.8 to 1.2: Idling
    • 0 to 0.999 = Rich

    • 1 = Stoichiometric A/F

    • 1.001 to 1.999 = Lean

    AF Lambda B1S1

    Short-term fuel trim associated with sensor 1:

    Min.: 0, Max.: 1.999


    • Value less than 1 (0.000 to 0.999) = Rich

    • Stoichiometric air-fuel ratio = 1

    • Value greater than 1 (1.001 to 1.999) = Lean

    -
    AFS Voltage B1S1

    Air fuel ratio sensor output voltage for sensor 1:

    Min.: 0 V, Max.: 7.9 V

    3.1 to 3.4 V: Idling, engine warmed up Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    AFS Current B1S1

    Air fuel ratio sensor current for sensor 1:

    Min.: -128 mA, Max.: 127.99 mA

    -

    Click here

    O2S B1S2

    Heated oxygen sensor output voltage for sensor 2:

    Min.: 0 V, Max.: 1.2 V

    0.1 to 0.9 V:

    Driving at 50 km/h (31 mph)

    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
    Short FT #1

    Short-term fuel trim:

    Min.: -100%, Max.: 99.2%

    -20 to 20 % Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1

    Long-term fuel trim:

    Min.: -100%, Max.: 99.2%

    -30 to 30 % Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
    Total FT #1

    Total fuel trim value for fuel system:

    Min.: -0.5, Max.: 0.496

    -0.2 to 0.2 -
    Fuel System Status #1

    Fuel system status (bank 1):

    OL or CL or OLDRIVE or OLFAULT or CLFAULT

    CL: Idling after warming up
    • OL (Open Loop): Has not yet satisfied conditions to go closed loop


    • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control


    • OLDrive: Open loop due to driving conditions (fuel enrichment)


    • OLFault: Open loop due to detected system fault


    • CLFault: Closed loop but heated oxygen sensor, which is used for fuel control, malfunctioning

    Fuel System Status #2 Fuel system status (bank 2) Unused
    IGN Advance

    Ignition timing advance for No. 1 cylinder:

    Min.: -64 deg, Max.: 63.5 deg

    BTDC 3 to 7 deg: Idling -
    Knock Feedback Value

    Knock feedback value:

    Min.: -64 CA, Max.: 1984 CA

    -20 to 0 CA:

    Driving at 70 km/h (44 mph)

    Service data
    Knock Correct Learn Value

    Knock correction learning value:

    Min.: -64 CA, Max.: 1984 CA

    0 to 20 CA:

    Driving at 70 km/h (44 mph)

    Service data
    Target EGR Position

    Target EGR position:

    Min.: 0% Max.: 100%

    - -
    EGR Step Position

    EGR step position:

    Min.: 0 STEP, Max.: 120 STEP

    - -
    VVT Control Status #1

    VVT control (bank 1) status:

    ON or OFF

    - Active Test support data
    VVT Aim Angle #1*4

    VVT aim angle (bank 1):

    Min.: 0%, Max.: 100%

    0 to 100% VVT duty signal value during intrusive operation (Active Test)
    VVT Change Angle #1*4

    VVT change angle (bank 1):

    Min.: 0°FR, Max.: 60°FR

    0 to 56°FR Displacement angle during intrusive operation (Active Test)
    VVT OCV Duty #1*4

    VVT OCV operation duty:

    Min.: 0%, Max.: 100%

    0 to 100% Requested duty value for intrusive operation (Active Test)
    Catalyst Temp B1S1

    Estimated catalyst temperature (bank 1, sensor 1):

    Min.: -40°C, Max.: 6513.5°C

    - -
    Catalyst Temp B1S2

    Estimated catalyst temperature (bank 1, sensor 2):

    Min.: -40°C, Max.: 6513.5°C

    - -
    Starter Signal

    Starter switch signal (STA terminal input status):

    ON or OFF

    ON: Cranking -
    Power Steering Signal

    Power steering signal:

    ON or OFF

    ON: Power steering operation -
    Power Steer. Sig. Record

    Power steering signal (history):

    ON or OFF

    ON: When steering wheel first turned after battery terminals connected Signal status usually ON until battery terminals disconnected
    Neutral Position SW Signal

    Park/neutral position switch status:

    ON or OFF

    - -

    Clutch Switch

    *1

    Clutch Switch

    ON or OFF

    ON: Clutch pedal depressed -

    Reverse Switch

    *1

    Reverse Switch

    ON or OFF

    ON: Shift lever in R -
    Stop Light Switch

    Stop light switch:

    ON or OFF

    ON: Brake pedal depressed -

    Shift Indication Enable

    *1

    Shift Indication Enable:

    ON or OFF

    - -
    A/C Signal

    A/C signal:

    ON or OFF

    ON: A/C ON -
    Closed Throttle Position SW

    Closed throttle position switch:

    ON or OFF


    • ON: Throttle fully closed


    • OFF: Throttle open

    -
    Fuel Cut Condition

    Fuel cut status:

    ON or OFF

    ON: Any fuel cut operation executed (idle fuel cut, light load fuel cut, etc.) -
    Immobiliser Communication

    Immobiliser status:

    ON or OFF

    ON: Under engine normal operation OFF: Immobiliser communication line ground short, or immobiliser set to prohibit engine start
    Electrical Load Signal

    Electrical load signal:

    ON or OFF

    ON: Headlights or defogger turned ON -
    Check Mode

    Check mode:

    ON or OFF

    ON: Check mode ON

    Click here

    SPD Test Result

    Check mode result for vehicle speed sensor:

    Compl or Incmpl

    - -
    Misfire Test Result

    Check mode result for misfire monitor:

    Compl or Incmpl

    - -
    OXS1 Test Result

    Check mode result for HO2 sensor:

    Compl or Incmpl

    - -
    A/F Test Results #1

    Check mode result for air-fuel ratio sensor:

    Compl or Incmpl

    - -
    Complete Parts Monitor

    Comprehensive component monitor:

    Not Avl or Avail

    - -
    Fuel System Monitor

    Fuel system monitor:

    Not Avl or Avail

    - -
    Misfire Monitor

    Misfire monitor:

    Not Avl or Avail

    - -
    EGR/VVT Monitor

    EGR/VVT Monitor:

    Not Avl or Avail

    - -
    EGR/VVT Monitor

    EGR/VVT Monitor:

    Compl or Incmpl

    - -
    O2S(A/FS) Heater Monitor

    O2S(A/FS) Heater Monitor:

    Not Avl or Avail

    - -
    O2S(A/FS) Heater Monitor

    O2S(A/FS) Heater Monitor:

    Compl or Incmpl

    - -
    O2S (A/FS) Monitor

    O2S (A/FS) monitor:

    Not Avl or Avail

    - -
    O2S (A/FS) Monitor

    O2S (A/FS) monitor:

    Compl or Incmpl

    - -
    A/C Monitor

    A/C Monitor:

    Not Avl or Avail

    - -
    A/C Monitor

    A/C Monitor:

    Compl or Incmpl

    - -
    2nd Air Monitor

    2nd Air Monitor:

    Not Avl or Avail

    - -
    2nd Air Monitor

    2nd Air Monitor:

    Compl or Incmpl

    - -
    EVAP Monitor

    EVAP Monitor:

    Not Avl or Avail

    - -
    EVAP Monitor

    EVAP Monitor:

    Compl or Incmpl

    - -
    Heated Catalyst Monitor

    Heated Catalyst Monitor:

    Not Avl or Avail

    - -
    Heated Catalyst Monitor

    Heated Catalyst Monitor:

    Compl or Incmpl

    - -
    Catalyst Monitor

    Catalyst monitor:

    Not Avl or Avail

    - -
    Catalyst Monitor

    Catalyst monitor:

    Compl or Incmpl

    - -
    # Codes (Include History)

    Number of codes:

    Min.: 0, Max.: 255

    - Number of detected DTCs
    MIL

    MIL status:

    ON or OFF

    ON: MIL ON -
    MIL ON Run Distance

    Distance traveled since MIL turned ON:

    Min.: 0 km, Max.: 65535 km

    Distance since DTC detected -
    Running Time from MIL ON

    Running time since MIL turned ON:

    Min.: 0 min

    Max.: 65535 min

    Equivalent to running time since MIL turned ON -
    Time After DTC Cleared

    Time since DTCs cleared:

    Min.: 0 min

    Max.: 65535 min

    Equivalent to time since DTCs cleared -
    Distance from DTC Cleared

    Distance traveled since DTCs cleared:

    Min.: 0 km, Max.: 65535 km

    Equivalent to distance driven since DTCs cleared -
    Warmup Cycle Cleared DTC

    Warm-up cycles since DTCs cleared:

    Min.: 0, Max.: 255

    - Number of warm-up cycles since DTCs cleared
    Number of Emission DTC Number of emission DTCs - -
    TC and TE1

    TC and CG (TE1) terminals of DLC3:

    ON or OFF

    - Active Test support data
    Ignition Trig. Count

    Ignition counter to calculate misfire rate:

    Min.: 0, Max.: 800

    0 to 300 -
    Cylinder #1 Misfire Count

    Misfire count of No. 1 cylinder:

    Min.: 0, Max.: 255

    0 -
    Cylinder #2 Misfire Count

    Misfire count of No. 2 cylinder:

    Min.: 0, Max.: 255

    0 -
    Cylinder #3 Misfire Count

    Misfire count of No. 3 cylinder:

    Min.: 0, Max.: 255

    0 -
    All Cylinders Misfire Count

    Misfire count of all cylinders:

    Min.: 0, Max.: 255

    0 -
    Misfire RPM

    Average of engine speed when misfire occurs:

    Min.: 0 rpm, Max.: 6375 rpm

    - -
    Misfire Load

    Average of engine load when misfire occurred:

    Min.: 0 g/rev, Max.: 3.98 g/rev

    - -
    Misfire Margin

    Margin to detect engine misfire:

    Min.: -100%, Max.: 99.22%

    -100 to 99.22% Misfire detection margin
    Electric Fan Motor

    Electric fan motor:

    ON or OFF

    ON: Electric fan motor operating Active Test support data
    Idle Fuel Cut

    Fuel cut idle:

    ON or OFF

    ON: Fuel cut operation (throttle valve fully closed) Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 1500 rpm
    FC TAU

    Fuel cut TAU (Fuel cut with very light load):

    ON or OFF

    ON: Fuel cut operating (throttle valve slightly opened) Fuel cut being performed with very light load to prevent incomplete engine combustion
    Model Code Identifying model code KSP90# -
    Engine Type Identifying engine type 1KRFE -
    Cylinder Number

    Identifying cylinder number:

    Min.: 0, Max.: 255

    3 -
    Transmission Type Identifying transmission type M/T, CVT -
    Destination Identifying destination W -
    Model Year

    Identifying model year:

    Min.: 1900, Max.: 2155

    2008 -
    System Identification Identifying engine system Gasoline -
    Engine Speed of Cyl #1

    Engine rpm during No. 1 cylinder fuel cut:

    Min.: 0 rpm, Max.: 51199 rpm

    - Output only when Check the Cylinder Compression performed using Active Test
    Engine Speed of Cyl #2

    Engine rpm during No. 2 cylinder fuel cut:

    Min.: 0 rpm, Max.: 51199 rpm

    - Output only when Check the Cylinder Compression performed using Active Test
    Engine Speed of Cyl #3

    Engine rpm during No. 3 cylinder fuel cut:

    Min.: 0 rpm, Max.: 51199 rpm

    - Output only when Check the Cylinder Compression performed using Active Test
    Av Engine Speed of All Cyl

    Average of engine rpm values during fuel cut of No. 1 to No. 3 cylinder:

    Min.: 0 rpm, Max.: 51199 rpm

    - Output only when Check the Cylinder Compression performed using Active Test

    MT Down Shift Indication

    *1

    MT Down Shift Indication

    ON or OFF

    - -

    MT Up Shift Indication

    *1

    MT Up Shift Indication

    ON or OFF

    - -

    *1: for Manual transaxle

    *2: for CVT

    Tech Tips


    • *3: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).

    • *4: Data List values are displayed only when performing the Active Test related to the VVT system. For other Active Tests, the Data List value will be 0.

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    • Data List can be displayed during Active Test.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    5. Perform the Active Tests by referring to the table below.

    Tester Display Test Part Control Range Diagnostic Note
    Control the Injection Volume Change injection volume Between -12.5 and 25.0%
    • All fuel injectors tested at same time


    • Confirm that the engine speed is 3000 rpm or less


    • Injection volume can be changed in 0.1% graduations within control range

    Control the Injection Volume for A/F Sensor Change injection volume Lower by 12.5% or increase by 25.0%
    • Confirm that the engine speed is 3000 rpm or less

    • Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs

    • To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F Control System / AFS Voltage B1S1 and O2S B1S2

    Control the EGR Step Position Open or closed EGR valve From 0 to 110 steps
    • EGR valve fully closed at step position 0, and fully open at step position 110

    • Amount of EGR gas, flowing into intake manifold, varies in accordance with EGR valve opening angle

    Activate the VSV for Evap Control Activate purge VSV control ON/OFF -
    Control the Fuel Pump / Speed Activate fuel pump (C/OPN Relay) ON/OFF Test is possible with engine stopped
    Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
    • ON: TC and TE1 connected


    • OFF: TC and TE1 disconnected

    Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
    Control the Electric Cooling Fan Control electric cooling fan ON/OFF -
    Control the ETCS Open/Close Slow Speed Throttle actuator ON: Throttle valve opens/closes slowly

    Test is possible when following conditions are met:


    • Engine is stopped


    • Shift lever in P


    • Accelerator pedal fully depressed.

    Control the ETCS Open/Close Fast Speed Throttle actuator ON: Throttle valve opens/closes fast
    Control the VVT Linear (Bank 1) Control VVT (bank 1)

    -128 to 127%

    This value added to present OCV control duty

    100%: Maximum advance

    -100%: Maximum retard

    Engine stalls or idles roughly when VVT actuator is operated by 100%.

    Test is possible with vehicle stopped and engine idling.

    Control the VVT System (Bank 1) Control VVT (bank 1) -128 to 127%

    Engine stalls or idles roughly when VVT actuator is operated

    Test is possible with vehicle stopped and engine idling

    Control the Cylinder #1 Fuel Cut No. 1 cylinder injector fuel cut ON/OFF

    Shift lever in P

    Test is possible with vehicle stopped and engine idling.

    Control the Cylinder #2 Fuel Cut No. 2 cylinder injector fuel cut ON/OFF
    Control the Cylinder #3 Fuel Cut No. 3 cylinder injector fuel cut ON/OFF
    Control the All Cylinders Fuel Cut All cylinders injector fuel cut ON/OFF

    Shift lever in P

    Test is possible with vehicle stopped

    Check the Cylinder Compression Check cylinder compression pressure ON/OFF *1

    Tech Tips

    *1: When performing the Active Test item "Check the Cylinder Compression" and then cranking the engine, the ECM stops fuel injection and the ignition, and measures the engine speed for each cylinder.

    If one cylinder speed is higher than the others, that cylinder's compression pressure can be concluded to be lower than the others.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the tester on.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    7. Select the following monitor items: Engine Speed of Cyl #1 to #3, Av Engine Speed of All Cyl

    8. Press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

      Tech Tips

      Fuel injection and ignition for all cylinders are prohibited at this time, and each cylinder's engine speed measurement will enter standby mode.

    9. Crank the engine until the monitor item values "Engine speed of Cyl #1 to #3" and "Av Engine Speed of All Cyl" change

    10. Monitor the engine speed (Engine Speed of Cyl #1 to #3, Av Engine Speed of All Cyl) displayed on the tester.

      Tech Tips

      The tester displays the values to be extremely high before cranking the engine. Each cylinder's engine speed is measured while cranking the engine and then the tester displays the actual engine speed values.

      Note


      • The Active Test item "Check the Cylinder Compression" will automatically turn off 255 seconds after the Active Test is turned on.

      • When the "Check the Cylinder Compression" is OFF and the engine is cranked, the engine will start.

      • If the "Check the Cylinder Compression" test needs to be performed again after each cylinder's engine speed measurement has been performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.

      • Use a fully-charged battery.