BLOWER RESISTOR (for Manual Air Conditioning System) INSTALLATION


  1. INSTALL BLOWER RESISTOR

    A0118HE

    1. Install the blower resister with the 2 screws.

    2. Connect the connector.

  2. INSTALL LOWER INSTRUMENT PANEL

    A011A3U

    1. Engage the 2 claws and 4 clips.

    2. Install the lower instrument panel with the 3 <F> bolts and <E> screw.

  3. INSTALL ROOM TEMPERATURE SENSOR (COOLER THERMISTOR)

    A011AAK

    1. Connect the connector.

    2. Engage the 2 claws and install the room temperature sensor.

  4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

    A0119AW

    1. Engage the 3 claws and install the air duct.

    2. Install the clip.

    3. A011AN2

      Connect the connector.

      Tech Tips

      If the vehicle is equipped with stop and start system, connect the connector.

  5. INSTALL INSTRUMENT CLUSTER FINISH NO. 1 PANEL

    A011B9S

    1. Engage the 9 clips and install the instrument cluster finish No. 1 panel.

  6. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    A0118NX

    1. Engage the 6 clips.

    2. Install the upper instrument panel with the <F> bolt.

  7. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY


    1. A011BQN

      Engage the 2 guides and install the knee airbag assembly.

    2. Install the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  8. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

    A011BUZ

    1. Engage the 4 claws and 2 clips.

    2. A011ARPE01
      Text in Illustration
      *1 Protective Tape

      Remove the protective tape.

    3. Install the lower No. 2 instrument panel with the <C> bolt.

  9. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A0118KA

    1. Engage the 3 claws and connect the hood lock control lever.

    2. A011AQB

      Connect the connector.

    3. Engage the 2 claws and connect the DLC3 connector.

    4. A011AI9

      Engage the 2 claws and 7 clips.

    5. Install the lower No. 1 instrument panel finish panel with the 2 <C> bolts.

  10. INSTALL COWL SIDE TRIM BOARD RH

    A0117YC

    1. Engage the guide and 2 claws and install the cowl side trim board.

  11. INSTALL COWL SIDE TRIM BOARD LH

    Tech Tips

    Use the same procedure as for the RH side.

  12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  14. INSTALL FRONT DOOR SCUFF PLATE RH

    A011AJ3

    1. Engage the 9 claws and install the front door scuff plate.

  15. INSTALL FRONT DOOR SCUFF PLATE LH

    Tech Tips

    Use the same procedure as for the RH side.

  16. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Connect all the connectors.

    2. A0118U2

      Engage the 2 claws and connect the air mix damper control cable.

    3. A0119IL

      Engage the 2 claws and connect the No. 2 heater control cable.

    4. A0119H7

      Engage the 8 clips and install the lower center instrument cluster finish panel.

  17. INSTALL FRONT CONSOLE BOX COVER

    A0117DU

    1. Engage the 2 claws and 4 clips and install the front console box cover.

  18. INSTALL REAR CONSOLE BOX ASSEMBLY

    A011B2F

    1. Engage the 2 front clips.

    2. Rotate the 2 rear clips in the direction indicated by the arrows to engage them and install the console box assembly RR.

  19. INSTALL CONSOLE UPPER PANEL SUB-ASSEMBLY (for CVT)


    1. A0118XU

      Engage the 8 claws and install the console upper panel.

  20. INSTALL CONSOLE UPPER PANEL SUB-ASSEMBLY (for Manual Transaxle)

    A0118HP

    1. Install the shifting hole cover onto the shift lever.

    2. Engage the 8 claws and install the console upper panel.

  21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for CVT)


    1. Install the shift lever knob onto the shift lever.

  22. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

    A0119TE

    1. Turn the shift lever knob clockwise and install the shift lever knob onto the shift lever.

  23. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL


    1. Connect the all connectors.

    2. A0117Z8

      Engage the 6 clips.

    3. Install the center No. 1 instrument cluster finish panel with the 2 bolts.

  24. INSTALL CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL

    A0118YB

    1. Connect the all connectors.

    2. Engage the 2 claws and connect the air inlet damper control cable.

    3. A011B0P

      Engage the 4 clips and install the center lower instrument cluster finish panel.

  25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  26. INSPECT SRS WARNING LIGHT

    Click here