ENTRY AND START SYSTEM (for Entry Function) Front Passenger Side Door Entry Lock Function does not Operate

DESCRIPTION

If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter is normal. The malfunctioning part may be the entry lock sensor circuit (front door outside handle assembly (for passenger side) (entry lock sensor) → certification ECU).

WIRING DIAGRAM

A011A9YE02

INSPECTION PROCEDURE

Note


  • The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.

  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3, and turn a courtesy light switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) Click here

    OK

  2. READ VALUE USING TECHSTREAM (DOOR LOCK POSITION SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FR Door Lock Pos*1 Front RH door lock position switch signal / ON or OFF

      ON: Front RH door unlocked

      OFF: Front RH side door locked

      		 -
      FL Door Lock Pos*2 Front LH door lock position switch signal / ON or OFF

      ON: Front LH side door unlocked

      OFF: Front LH side door locked

      		 -

      • *1: for LHD

      • *2: for RHD

      OK
      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
      Result
      Result Proceed to
      OK A
      NG

      B

      (Refer to "Only Passenger Door LOCK/UNLOCK Functions do not Operate" in the problem symptoms table)

    B

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) Click here

    A

  3. READ VALUE USING INTELLIGENT TESTER (P-DOOR TRIGGER SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Entry and Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P-Door Trigger SW Front passenger side door lock sensor / ON or OFF

      ON: Entry lock sensor touched

      OFF: Entry lock sensor touched

      		 -
      OK
      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.

    NG

    CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU) Click here

    OK

    REPLACE CERTIFICATION ECU

  4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)


    1. A0119TVE06
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Front Door Outside Handle)
      *2

      Front view of wire harness connector

      (to Certification ECU)
      *3 for LHD
      *4 for RHD

      Disconnect the certification ECU connector.

    2. Disconnect the front door outside handle (for passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q1-1 (TRG+) - D34-19 (TSW2)*1 Always Below 1 Ω
      R1-1 (TRG+) - D34-19 (TSW2)*2 Always Below 1 Ω
      D34-19 (TSW2) - Body ground Always 10 kΩ or higher

      • *1: for LHD

      • *2: for RHD


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE)


    1. Reconnect the certification ECU and front door outside handle assembly (for passenger side) connector.

      A011B64E03
      Text in Illustration
      *1

      Component with harness connected

      (Certification ECU)

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D34-19 (TSW2) - D34-15 (E) Engine switch off, all doors closed, and lock sensor (passenger side) off → on Pulse generation → Below 2V

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE) Click here

    OK

    REPLACE CERTIFICATION ECU