FRONT DOOR LOCK INSPECTION


  1. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)


    1. A011AEXE04
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock LH)

      Check the operation of the door lock motor.


      1. Apply battery voltage to the motor terminals.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (L)

        Battery negative (-) → 1 (UL)

        		 Locks

        Battery positive (+) → 1 (UL)

        Battery negative (-) → 4 (L)

        		 Unlocks

        If the result is not as specified, replace the door lock.

    2. w/ Unlock detection switch:

      Check the resistance of the unlock detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        7 (E) - 8 (LSSR) Locked 10 kΩ or higher
        7 (E) - 8 (LSSR) Unlocked Below 1 Ω

        If the result is not as specified, replace the door lock.

    3. A011AVKE04
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock LH)

      w/ Door lock and unlock switch:

      Check the resistance of the door lock and unlock switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        7 (E) - 9 (L) Locked Below 1 Ω
        7 (E) - 9 (L) Unlocked 10 kΩ or higher
        7 (E) - 10 (UL) Locked 10 kΩ or higher
        7 (E) - 10 (UL) Unlocked Below 1 Ω

        If the result is not as specified, replace the door lock.

  2. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)


    1. A0119EKE01
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock LH)

      Check the operation of the door lock motor.


      1. Apply battery voltage to the motor terminals.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (L)

        Battery negative (-) → 3 (UL)

        		 Locks

        Battery positive (+) → 3 (UL)

        Battery negative (-) → 4 (L)

        		 Unlocks

        If the result is not as specified, replace the door lock.

    2. A011BK5E01
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock LH)

      Check the resistance of the unlock detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        7 (E) - 8 (LSSR) Locked 10 kΩ or higher
        7 (E) - 8 (LSSR) Unlocked Below 1 Ω

        If the result is not as specified, replace the door lock.

    3. A011AGUE01
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock LH)

      Check the operation of the double door lock motor.


      1. Apply battery voltage to the double door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 2 (DL)

        Battery negative (-) → 1 (UNDL)

        		 Set

        Battery positive (+) → 1 (UNDL)

        Battery negative (-) → 2 (DL)

        		 Unset

        Tech Tips


        • Set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

        • Unset the double locking system. Check that the doors can be unlocked by operating the control cable.

        If the result is not as specified, replace the door lock.

    4. Check the operation of the double lock position switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        5 (E) - 6 (DLSR) Unset 10 kΩ or higher
        5 (E) - 6 (DLSR) Set Below 1 Ω

        If the result is not as specified, replace the door lock.

  3. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)


    1. A0119IXE03
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock RH)

      Check the operation of the door lock motor.


      1. Apply battery voltage to the motor terminals.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (L)

        Battery negative (-) → 1 (UL)

        		 Locks

        Battery positive (+) → 1 (UL)

        Battery negative (-) → 4 (L)

        		 Unlocks

        If the result is not as specified, replace the door lock.

    2. Check the resistance of the unlock detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        7 (LSSR) - 8 (E) Locked 10 kΩ or higher
        7 (LSSR) - 8 (E) Unlocked Below 1 Ω

        If the result is not as specified, replace the door lock.

    3. A011963E04
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock RH)

      w/ Door lock and unlock switch:

      Check the resistance of the door lock and unlock switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        6 (L) - 8 (E) Locked Below 1 Ω
        6 (L) - 8 (E) Unlocked 10 kΩ or higher
        5 (UL) - 8 (E) Locked 10 kΩ or higher
        5 (UL) - 8 (E) Unlocked Below 1 Ω

        If the result is not as specified, replace the door lock.

  4. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)


    1. A011B1XE01
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock RH)

      Check the operation of the door lock motor.


      1. Apply the battery voltage to the motor terminals.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 2 (L)

        Battery negative (-) → 1 (UL)

        		 Locks

        Battery positive (+) → 1 (UL)

        Battery negative (-) → 2 (L)

        		 Unlocks

        If the result is not as specified, replace the door lock.

    2. Check the resistance of the unlock detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        7 (LSSR) - 8 (E) Locked 10 kΩ or higher
        7 (LSSR) - 8 (E) Unlocked Below 1 Ω

        If the result is not as specified, replace the door lock.

    3. A01181AE01
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock RH)

      Check the resistance of the door lock and unlock switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        6 (L) - 8 (E) Locked Below 1 Ω
        6 (L) - 8 (E) Unlocked 10 kΩ or higher
        5 (UL) - 8 (E) Locked 10 kΩ or higher
        5 (UL) - 8 (E) Unlocked Below 1 Ω

        If the result is not as specified, replace the door lock.

    4. A011AGUE02
      Text in Illustration
      *1

      Component without harness connected

      (Front Door Lock RH)

      Check the operation of the double door lock motor.


      1. Apply battery voltage to the double door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (DL)

        Battery negative (-) → 3 (UNDL)

        		 Set

        Battery positive (+) → 3 (UNDL)

        Battery negative (-) → 4 (DL)

        		 Unset

        Tech Tips


        • Set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

        • Unset the double locking system. Check that the doors can be unlocked by operating the control cable.

        If the result is not as specified, replace the door lock.

    5. Check the operation of the double lock position switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        9 (DLSR) - 10 (E) Unset 10 kΩ or higher
        9 (DLSR) - 10 (E) Set Below 1 Ω

        If the result is not as specified, replace the door lock.