FRONT DOOR LOCK REMOVAL


  1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A011AD3

      Disengage the clip and 2 guides and remove the front door lower frame bracket garnish.

  2. REMOVE FRONT ARMREST BASE UPPER PANEL (w/o Screw)


    1. A011BY2E01
      Text in Illustration
      *1 Moulding Remover

      Using a moulding remover, disengage the 6 claws and remove the front armrest base upper panel.

    2. Disconnect the connector.

  3. REMOVE FRONT ARMREST BASE UPPER PANEL (w/ Screw)


    1. A011BMRE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the door armrest cap.

    2. A01189G

      Remove the screw.

    3. A011BGVE01
      Text in Illustration
      *1 Moulding Remover

      Using a moulding remover, disengage the 6 claws and remove the front armrest base upper panel.

    4. Disconnect the connector.

    5. A011BMF

      Disengage the claw and remove the door armrest cap.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL


    1. A0119YHE02
      Text in Illustration
      *1 Moulding Remover

      Using a moulding remover, disengage the 4 claws and remove the front door inside handle bezel.

  5. REMOVE DOOR ASSIST GRIP COVER


    1. A01183RE01
      Text in Illustration
      *1 Moulding Remover

      Using a moulding remover, disengage the 6 claws and remove the door assist grip cover.

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A011AF2

      Disconnect the connector.

    2. Remove the 3 screws.

    3. A011928

      Disengage the 10 clips and 6 claws.

    4. A011AHT

      Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.

  7. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A011B0Y

      Remove the bolt and remove the ground wire.

    2. Disconnect the connector.

    3. Disengage the clamps, and then remove the front door service hole cover.

      Note

      Remove any tape remaining on the door side.

  8. REMOVE FRONT DOOR FRAME REAR LOWER SUB-ASSEMBLY


    1. A0118IB

      Remove the bolt and remove the front door frame rear lower sub-assembly.

      Note

      Do not drop or damage the front door frame rear lower sub-assembly when removing the bolt.

      Tech Tips

      Remove the front door frame rear lower sub-assembly through the service hole.

  9. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for RHD)


    1. A011BGE

      Remove the hole plug.

    2. Using "TORX" socket wrench T30, loosen the screw and remove the cover.

    3. A011BSC

      Disengage the 2 claws and remove the lock cylinder.

  10. REMOVE FRONT DOOR LOCK ASSEMBLY


    1. A011BC7

      Using a "TORX" socket wrench T30, remove the 3 screws.

    2. Slide the front door lock downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock and cables as a unit.

    3. Remove the door lock wire harness seal from the front door lock.

  11. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE


    1. A011BWN

      Remove the front door lock remote control cable.

    2. A011ARBE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and open the cover.

  12. REMOVE FRONT DOOR INSIDE LOCKING CABLE


    1. A011AND

      Remove the front door inside locking cable.