ENTRY AND START SYSTEM (for Entry Function) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start or Main Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Entry and Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D-Door Touch Sensor Driver side door touch sensor / ON or OFF

      ON: Sensor touched

      OFF: Sensor not touched

      		 -
      P-Door Touch Sensor Front passenger side door touch sensor / ON or OFF

      ON: Sensor touched

      OFF: Sensor not touched

      		 -
      D-Door Trigger Switch Driver side door lock switch / ON or OFF

      ON: Switch pushed

      OFF: Switch not pushed

      		 -
      P-Door Trigger Switch Front passenger side door lock switch / ON or OFF

      ON: Switch pushed

      OFF: Switch not pushed

      		 -
      Tr/B-Door Lock SW Back door lock switch / ON or OFF

      ON: Back door lock switch pushed

      OFF: Back door lock switch not pushed

      		 -
      Tr/B-Door Unlock SW Back door unlock switch / ON or OFF

      ON: Back door unlock switch pushed

      OFF: Back door unlock switch not pushed

      		 -
      Ignition Switch Engine switch / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      Unmatched Vehicle-ID Communication condition between vehicle and electrical key transmitter (vehicle-ID) / Yes or No

      Yes: Key ID code matched to vehicle

      No: Key ID code not matched to vehicle

      		 -
      No Response Communication condition between vehicle and electrical key transmitter (response) / Yes or No

      Yes: Key ID code matched to vehicle

      No: Key ID code not matched to vehicle

      		 -
      Unmatch Code or Form Communication condition between vehicle and electrical key transmitter (response code and format) / Yes or No

      Yes: Key ID code matched to vehicle

      No: Key ID code not matched to vehicle

      		 -
      Key Low Battery Low key battery / Yes or No

      Yes: Key battery voltage low

      No: Key battery voltage normal

      		 -
      Power Save Cnt 10 Min Power save counter - 10 minutes / Min: 0; Max: 255 Within range from 0 to 255 -
      Power Save Cnt 5 Day Power save counter - 5 days / Min: 0; Max: 255 Within range from 0 to 255 -
      Power Save Cnt 14 Day Power save counter - 14 days / Min: 0; Max: 255 Within range from 0 to 255 -
      ID Code Difference(Resp) Communication condition between vehicle and electrical key transmitter (ID code) / Yes or No

      Yes: Key ID code matched to vehicle

      No: Key ID code not matched to vehicle

      		 -
      C Code Difference Communication condition between vehicle and electrical key transmitter (challenge code) / Yes or No

      Yes: Key ID code matched to vehicle

      No: Key ID code not matched to vehicle

      		 -
      Auto Entry Cancel SW Entry function cancel / ON or OFF Mode status displayed -
      Ignition Available Area Ignition available area / FRONT or ALL Customization status displayed -
      Parking Wait Time Parking wait time / 0.5s, 1.5s, 2.5s, 5s Customization status displayed -
      B-Dr Opening Operation Back door opening operation / LONG, TWICE, OFF Customization status displayed -
      Key Low Battery Warning Low key battery warning / ON or OFF Customization status displayed -
      Key Left in Vehicle BUZ Key left in vehicle buzzer / ON or OFF Customization status displayed -
      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Engine switch on (ACC) / ON or OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 -
      IG SW Engine switch on (IG) / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      Back Door Courtesy SW Back door courtesy light switch signal / ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      FR Door Lock Pos Front RH door lock position switch signal / ON or OFF

      ON: Front RH door unlocked

      OFF: Front LH side door locked

      		 -
      FR Door Courtesy Front RH door courtesy light switch signal / ON or OFF

      ON: Front RH door opened

      OFF: Front RH door closed

      		 -
      FL Door Lock Pos Front LH door lock position switch signal / ON or OFF

      ON: Front LH side door unlocked

      OFF: Front LH side door locked

      		 -
      FL Door Courtesy Front LH door courtesy light switch signal / ON or OFF

      ON: Front LH door opened

      OFF: Front LH door closed

      		 -
      Back Door Open Handle Back door open switch / ON or OFF

      ON: Back door open switch pushed

      OFF: Back door open switch not pushed

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start or Main Body / Active Test.

    5. Perform the Active Test according to the display on the intelligent tester.

      Entry and Start
      Tester Display Test Part Control Range Diagnostic Note
      Overhead Tuner Power Supply ON Door control receiver ON/OFF -
      Power for P-Seat Sens Door electrical key oscillator (for front passenger side) ON/OFF -
      Power/Engine SW Light Engine switch illumination ON/OFF -
      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Trunk and Back-door Open Back door lock motor ON/OFF -
      Wireless Buzzer Wireless door lock buzzer ON/OFF -