VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1432

DTC Code DTC Name
C1432 Steering Angle Sensor Power Source Voltage Malfunction

DESCRIPTION

Signals from the steering sensor (built in to the spiral cable) are sent to the skid control ECU (built in to the brake actuator assembly) through CAN communication.

DTC Code DTC Detection Condition Trouble Area
C1432 Steering angle sensor power supply malfunction signal is received from steering angle sensor.

  • Steering angle sensor power supply

  • Steering angle sensor (built into the spiral cable)

WIRING DIAGRAM

A0117WXE02

INSPECTION PROCEDURE

Note


  • Do not remove the steering sensor from the spiral cable.

  • When replacing the spiral cable, confirm that the replacement part is of the correct specification.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips


  • When U0073, U0123, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0123, U0124 and/or U0126 first Click here.

  • When the speed sensor or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.

PROCEDURE


  1. INSPECT STEERING ANGLE SENSOR (BAT TERMINAL)


    1. A011BGJE03
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Steering Angle Sensor)

      Turn the ignition switch off.

    2. Remove the steering wheel and the column cover lower.

    3. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    4. Disconnect the D20 steering angle sensor connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      D20-6 (BAT) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

    OK

  2. INSPECT STEERING ANGLE SENSOR (IG1 TERMINAL)


    1. A011BGJE04
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Steering Angle Sensor)

      Turn the ignition switch ON.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      D20-5 (IG) - Body ground Ignition switch ON 11 to 14 V
      Result
      Result Proceed to
      OK A
      NG (w/ Stop and Start System) B
      NG (w/o Stop and Start System) C

    B

    GO TO STOP AND START SYSTEM Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

    A

  3. INSPECT STEERING ANGLE SENSOR (GND TERMINAL)


    1. A011BGJE02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Steering Angle Sensor)

      Turn the ignition switch off.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D20-2 (ESS) - Body ground Always Below 1 Ω

      Tech Tips

      If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GND)

    OK

    REPLACE SPIRAL CABLE (STEERING ANGLE SENSOR) Click here