FRONT DRIVE SHAFT ASSEMBLY (for 1ND-TV) DISASSEMBLY


  1. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP


    1. A0118VG

      Using a screwdriver, release the staked part of the boot clamp and separate the boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  2. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP


    1. A011BXC

      Using a screwdriver, release the staked part of the boot clamp and separate the boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  3. SEPARATE FRONT AXLE INBOARD JOINT BOOT


    1. Separate the inboard joint boot from the inboard joint grommet.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY


    1. Remove the old grease from the inboard joint.

    2. A011ALUE04
      Text in Illustration
      *1 Matchmark

      Place matchmarks on the inboard joint and outboard joint shaft.

      Note

      Do not cause any damage when placing the marks.

    3. Remove the inboard joint from the outboard joint shaft.

    4. Fix the outboard joint shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    5. A011749

      Using a snap ring expander, remove the snap ring.

    6. A011BMUE06
      Text in Illustration
      *1 Matchmark

      Place matchmarks on the tripod joint and outboard joint shaft.

      Note

      Do not cause any damage when placing the marks.

    7. Using a brass bar and hammer, remove the tripod joint.

      Note

      Do not tap the rollers.

    8. Remove the No. 2 inboard joint boot clamp, the inboard joint boot and the inboard joint boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  5. REMOVE FRONT AXLE INBOARD JOINT GROMMET


    1. Remove the inboard joint grommet from the inboard joint.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  6. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side)

    A0119MOE01
    Text in Illustration
    *1 One Touch Type
    *2 Claw Engagement Type

    1. One touch type:


      1. Using a screwdriver, release the staked part of the damper clamp and separate the damper clamp.

    2. Claw engagement type:


      1. Using needle-nose pliers, disengage the 2 claws and remove the damper clamp.

    3. Remove the front drive shaft damper from the front axle outboard joint shaft assembly.

  7. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP


    1. A01183A

      Using a screwdriver, release the staked part of the boot clamp and remove the boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  8. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP


    1. A011BF8

      Using a screwdriver, release the staked part of the boot clamp and remove the boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT


    1. Remove the outboard joint boot from the outboard joint shaft.

    2. Remove the old grease from the outboard joint.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  10. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH


    1. A0117U4

      Using a screwdriver, remove the snap ring.

  11. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING RH

    Tech Tips

    Use the same procedure for the RH side as for the LH side.

  12. REMOVE FRONT DRIVE SHAFT DUST COVER


    1. A0118DWE02

      Using SST and a press, remove the dust cover.

      SST
      09950-00020

      Note

      Do not drop the inboard joint.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.