OIL AND OIL FILTER REPLACEMENT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. Skin should be washed with soap and water, or use waterless hand cleaner, to thoroughly remove any used engine oil. Do not use gasoline, thinners, or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and drain the engine oil into a container.

    3. Install a new gasket and the oil pan drain plug.

      Torque:
      30 N*m  { 301 kgf*cm, 22 ft.*lbf }

  2. REMOVE OIL FILTER ELEMENT


    1. A0119ZDE02
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A011B5Y

      Remove the oil filter drain plug.

    3. A01176PE01
      Text in Illustration
      *1 Cap
      *2 Valve
      *3 Pipe
      *4 O-ring
      *5 Hose

      Install the pipe to the oil filter cap.

      Note

      If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

      Tech Tips

      Use a container to catch the draining oil.

    4. A01187N

      Check that oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration.

    5. Remove the O-ring.

    6. A01196ZE01

      Using SST, remove the oil filter cap.

      SST
      09228-06501
    7. A0118MNE02
      Text in Illustration
      *1 Oil Filter Element
      *2 O-ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove.

  3. INSTALL OIL FILTER ELEMENT


    1. A0118MNE02
      Text in Illustration
      *1 Oil Filter Element
      *2 O-ring

      Clean the inside of the oil filter cap, the threads and the O-ring groove.

    2. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

    3. Set a new oil filter element to the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily tighten the oil filter cap.

    6. A0117SYE04
      Text in Illustration
      *a No Clearance

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Note


      • Make sure that the oil filter is installed securely as shown in the illustration.

      • Be careful that the O-ring does not get caught between the parts.

    7. A011B15E04
      Text in Illustration
      *1 Oil Filter Drain Plug
      *2 O-ring

      Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

      Note

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. Install the oil filter drain plug.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Be careful that the O-ring does not get caught between the parts.

  4. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)

      • API grade SL "Energy-Conserving".

      • SM "Energy-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30

      • 10W-30
      API grade SL or SM multigrade engine oil

      • 15W-40

      • 20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill with oil filter change 3.7 liters (3.9 US qts, 3.3 Imp. qts)
      Drain and refill without oil filter change 3.5 liters (3.7 US qts, 3.1 Imp. qts)
      Dry fill 4.2 liters (4.4 US qts, 3.7 Imp. qts)

    2. Install the oil filler cap.

  5. INSPECT FOR ENGINE OIL LEAK