COOLANT REPLACEMENT

CAUTION:

Be sure that the ignition switch is off if you work near the electric cooling fans or radiator grille. With the ignition switch ON, the electric cooling fans may automatically start if the engine coolant temperature is high or the air conditioning is on.


  1. DRAIN ENGINE COOLANT

    CAUTION:

    To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

    A011B1KE01
    Text in Illustration
    *1 Water Filler Cap Sub-assembly *2 Radiator Drain Cock Plug
    *3 Air Bleed Valve - -

    1. Loosen the radiator drain cock plug.

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. Remove the water filler cap sub-assembly.

  2. ADD ENGINE COOLANT


    1. Tighten the radiator drain cock plug.

    2. A011AOTE01
      Text in Illustration
      *1 Air Bleed Valve

      Loosen the air bleed valve.

    3. Remove the water filler cap sub-assembly.

    4. A0119COE03
      Text in Illustration
      *a Filler Tube End
      *b Coolant Level

      Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler (Coolant level should be within 20 mm (0.787 in.) from the filler tube end).

      Standard Capacity
      Item Capacity
      M/T 4.7 liters (5.0 US qts, 4.1 Imp. qts)
      CVT 4.9 liters (5.2 US qts, 4.3 Imp. qts)

      Note

      Never use water as a substitute for engine coolant.

      Tech Tips

      TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    5. Remove the reserve tank cap.

      If the coolant level is low, add coolant.

    6. A0118S1E04
      Text in Illustration
      *a FULL Line

      Fill the radiator reserve tank with coolant to the FULL line.

    7. A011AOTE01
      Text in Illustration
      *1 Air Bleed Valve

      Tighten the air bleed valve.

    8. Install the water filler cap sub-assembly and reserve tank cap.

    9. Start the engine and warm it up.

    10. Bleed air from the cooling system.

      Tech Tips


      • Before starting the engine, turn the A/C switch off.

      • Adjust the air conditioning temperature setting to MAX (HOT).

      • Adjust the air conditioning blower setting to LO.


      1. Run the engine intermittently for 7 minutes or more (5 seconds running at 3000 rpm and 45 seconds idling, repeat several times).

    11. Stop the engine, and wait until the engine coolant cools down.

    12. A0118S1E05
      Text in Illustration
      *a FULL Line
      *b LOW Line

      After the engine is cooled down, check that the coolant level is between the FULL and LOW lines.

      If the coolant level is low, add coolant to the reservoir tank FULL line.

  3. INSPECT FOR COOLANT LEAK

    CAUTION:

    To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.


    1. A0119F8E01
      Text in Illustration
      *1 Radiator Cap Tester

      Fill the radiator assembly with engine coolant, and attach a radiator cap tester.

    2. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.

      If the pressure drops, check the hoses, radiator assembly and water pump assembly for leaks. If there are no signs or traces of external engine coolant leaks, check the heater core, cylinder block and head.