FUEL TANK INSTALLATION


  1. INSTALL NO. 1 EVAPORATION VENT TUBE CLAMP


    1. Engage the 2 claws and install the No. 1 evaporation tube clamp.

  2. INSTALL FUEL TANK VENT TUBE SUB-ASSEMBLY


    1. A011BWUE02
      Text in Illustration
      *a Arrows
      *b Recession

      Insert the fuel tank vent tube from the sender gauge side, in the direction indicated by the arrows on the fuel tank, run the tube along the bottom edge of the fuel tank, and then pull it out on the fuel pump side.

      Note

      Do not run the fuel tank vent tube on the other side of the recession shown in the illustration.

  3. INSTALL FUEL TANK SUCTION TUBE GASKET


    1. Install a new gasket to the fuel tank.

  4. INSTALL FUEL SUCTION TUBE ASSEMBLY


    1. A011A0PE01
      Text in Illustration
      *1 Retainer

      Line up the pipe and connector and push them together until a "click" sound is heard.

      Note


      • Check that there are no scratches or foreign objects on the pipe and connector before connecting them.

      • After connecting the pipe and connector, check that the pipe and connector are securely connected by pulling on them.

    2. Install the fuel suction tube assembly to the fuel tank.

  5. INSTALL FUEL PUMP GAUGE RETAINER


    1. A011B9NE02
      Text in Illustration
      *a Cutout

      Align the protrusion of the fuel suction tube assembly with the cutouts of the fuel tank.

      Note

      Ensure that the fuel suction tube gasket is in the correct position.

    2. While holding the fuel suction tube assembly by hand, position the fuel pump gauge retainer and tighten it lightly by hand.

      Note

      Check that the contact surface of the fuel tank retainer is not scratched or damaged and prevent the entry of foreign objects.

    3. A011912E01

      Using a 6 mm socket hexagon wrench, set SST to the fuel pump gauge retainer.

      SST
      09808-14020   ( 09808-01410, 09808-01420, 09808-01430 )

      Note

      Do not use any tools other than SST.

      Tech Tips


      • Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.

      • Align the ribs of the fuel pump gauge retainer with the tips of SST.

    4. A011A0SE02
      Text in Illustration
      *1 Starting Point
      *2 Lock Point
      *a Front of Vehicle
      *b Hold
      *c Turn

      Using SST, align the marks on the fuel tank and fuel pump gauge retainer.

      SST
      09808-14020   ( 09808-01410, 09808-01420, 09808-01430 )

  6. INSTALL FUEL TANK SUCTION TUBE GASKET


    1. Install a new gasket to the fuel tank.

  7. INSTALL FUEL TANK VENT TUBE ASSEMBLY


    1. Engage the 2 claws and connect the fuel tank vent tube sub-assembly to the fuel tank vent tube assembly.

    2. A0118KLE02
      Text in Illustration
      *a Arrows

      Rotate the fuel tank vent tube in the direction shown by the arrows, insert the sender gauge in the direction of the fuel tank gauge shown by the arrows, and then install the fuel tank vent tube assembly into the fuel tank.

      Note

      Do not bend the sender gauge arm.

  8. INSTALL FUEL PUMP GAUGE RETAINER


    1. A011AT4E02
      Text in Illustration
      *a Cutout

      Align the protrusion of the fuel tank vent tube assembly with the cutouts of the fuel tank.

      Note

      Ensure that the fuel suction tube gasket is in the correct position.

    2. While holding the fuel tank vent tube assembly by hand, position the fuel pump gauge retainer and tighten it lightly by hand.

      Note

      Check that the contact surface of the fuel tank retainer is not scratched or damaged and prevent the entry of foreign objects.

    3. A01184WE01

      Using a 6 mm socket hexagon wrench, set SST to the fuel pump gauge retainer.

      SST
      09808-14020   ( 09808-01410, 09808-01420, 09808-01430 )

      Note

      Do not use any tools other than SST.

      Tech Tips


      • Hold the fuel tank vent tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.

      • Align the ribs of the fuel pump gauge retainer with the tips of SST.

    4. A0117BWE03
      Text in Illustration
      *1 Starting Point
      *2 Lock Point
      *a Front of Vehicle
      *b Hold
      *c Turn

      Using SST, align the marks on the fuel tank and fuel pump gauge retainer.

      SST
      09808-14020   ( 09808-01410, 09808-01420, 09808-01430 )

  9. INSTALL NO. 1 CHARCOAL CANISTER OUTLET HOSE


    1. A011BELE01
      Text in Illustration
      *1 Yellow mark

      Install the No. 1 charcoal canister outlet hose onto the fuel tank vent tube assembly.

      Note

      Install the No. 1 charcoal canister outlet hose with its yellow mark toward the rear of the vehicle.

    2. Engage the No. 1 charcoal canister outlet hose.

  10. INSTALL NO. 2 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A0118A0E04
      Text in Illustration
      *1 Retainer
      *2 Fuel Tube Connector
      *3 O-Ring
      *4 Fuel Pipe
      *a Push

      Connect the No. 2 fuel evaporation tube to the fuel tank vent tube assembly and lock it by pushing in the retainer.

      Note


      • Check that there are no scratches or foreign objects on the connecting part.

      • Check that the No. 2 fuel evaporation tube is inserted securely.

      • After installing the retainer, check that the No. 2 fuel evaporation tube is securely connected by pulling on it.

    2. Engage the clamp and install the No. 2 fuel evaporation tube to the fuel tank.

  11. INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A011BC8E02
      Text in Illustration
      *1 Retainer
      *2 Fuel Tube Connector
      *3 O-Ring
      *4 Fuel Pipe
      *a Push

      Connect the No. 1 fuel evaporation tube to the fuel suction tube assembly and fuel tank vent tube assembly and lock them by pushing in the retainers.

      Note


      • Check that there are no scratches or foreign objects on the connecting part.

      • Check that the No. 1 fuel evaporation tube is inserted securely.

      • After installing the retainer, check that the No. 1 fuel evaporation tube is securely connected by pulling on it.

    2. Engage the clamp and install the No. 1 fuel evaporation tube to the fuel tank.

  12. INSTALL REAR FUEL EMISSION TUBE SUB-ASSEMBLY


    1. Connect the rear fuel emission tube to the fuel tank vent tube assembly.

    2. Engage the 2 clamps and install the fuel emission tube to the fuel tank.

  13. INSTALL FUEL TANK WIRE


    1. Install the fuel hose clamp to the fuel tank wire.

    2. Connect the fuel tank wire connectors to the fuel suction tube assembly and fuel tank vent tube assembly.

    3. Engage the 7 clamps and install the fuel tank wire to the fuel tank.

      Note

      After connecting the fuel tank wire connector, check that the fuel tank wire is inserted securely.

  14. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A0117WAE02
      Text in Illustration
      *1 Fuel Tube Connector
      *2 Tube Joint Clip
      *3 O-Ring
      *a OK
      *b NG

      Insert the fuel tank main tube into the fuel suction tube assembly plug and lock it with the tube joint clip.

      Note


      • Check that there are no scratches or foreign objects on the connecting part.

      • Check that the fuel tank main tube is inserted securely.

      • Check that the tube joint clip is on the collar of the fuel tank main tube.

      • After installing the tube joint clip, check that the fuel tank main tube is securely connected by pulling on it.

    2. Engage the clamp and install the fuel tank main tube to the fuel tank.

  15. INSTALL FUEL TANK CUSHION


    1. A011974E01
      Text in Illustration
      *1 No. 1 Fuel Tank Cushion
      *2 No. 2 Fuel Tank Cushion

      Install the No. 1 fuel tank cushions and the No. 2 fuel tank cushions at the locations indicated in the illustration.

  16. INSTALL FUEL TANK ASSEMBLY


    1. Clean and degrease the bolt holes.

    2. Set the fuel tank and 2 fuel tank bands on the engine lifter.

    3. Slowly raise the engine lifter and install the fuel tank onto the vehicle.

      Note

      Make sure that the fuel tank does not fall.

    4. A011BM1E01

      Tighten the 4 bolts in the sequence shown in the illustration, and secure the 2 fuel tank bands and the fuel tank.

      Torque:
      39 N*m  { 400 kgf*cm, 29 ft.*lbf }

  17. CONNECT REAR FUEL EMISSION TUBE SUB-ASSEMBLY


    1. A011BLBE02
      Text in Illustration
      *1 Retainer
      *2 Fuel Tube Connector
      *3 Fuel Pipe
      *4 O-Ring
      *a Push

      Connect the rear fuel emission tube and lock it by pushing in the retainer.

      Note


      • Check that there are no scratches or foreign objects on the connecting part.

      • Check that the rear fuel tank emission tube is inserted securely.

      • After installing the retainer, check that the rear fuel emission tube is securely connected by pulling on it.

  18. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A0117O9E03
      Text in Illustration
      *1 Retainer
      *2 Checker
      *3 Fuel Pipe
      *4 Fuel Tube Connector
      *5 O-Ring
      *a Push

      Line up the pipe and connector and push them together until a "click" sound is heard.

    2. Push the checker in to lock it.

      Note


      • Check that there are no scratches or foreign objects on the connecting part.

      • Check that the fuel tank main tube is inserted securely.

      • After installing the checker, check that the fuel tank main tube is securely connected by pulling on it.

  19. CONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY


    1. A0119UEE02
      Text in Illustration
      *1 Retainer
      *a Push

      Connect the inlet tube to the fuel tank assembly and lock it by pushing in the retainer.

      Note


      • Check that there are no scratches or foreign objects on the connecting part.

      • Check that the inlet tube is inserted securely.

      • After installing the retainer, check that the inlet tube is securely connected by pulling on it.

      Tech Tips


      • Insert the inlet tube until a "click" sound is heard.

      • The quick connector cannot be locked when the tube is not inserted securely.

    2. A011748E02
      Text in Illustration
      *1 Retainer
      *a Push

      Connect the fuel tank breather tube to the fuel tank assembly and lock it by pushing in the retainer.

      Note


      • Check that there are no scratches or foreign objects on the connecting part.

      • Check that the breather tube is inserted securely.

      • After installing the retainer, check that the breather tube is securely connected by pulling on it.

      Tech Tips

      The quick connector cannot be locked when the tube is not inserted securely.

  20. CONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE


    1. A01178LE01
      Text in Illustration
      *1 Yellow mark

      Connect the No. 1 charcoal canister outlet hose.

      Note


      • Install the No. 1 charcoal canister outlet hose with its yellow mark toward the rear of the vehicle.

      • After connecting the fuel tank breather tube and No. 1 charcoal canister outlet hose, check that the evaporation vent tube clamp is securely connected by pulling on it.

  21. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    1. Engage the claw and install the No. 1 fuel tank protector with the 2 clips and 4 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  22. CONNECT FUEL TANK WIRE


    1. Pull the fuel tank wire through the floor, install the grommet in the floor, and connect the fuel tank wire connector.

  23. ADD FUEL


    1. Open the fuel tank cap to add fuel.

  24. INSPECT FOR FUEL LEAK


    1. Check fuel pump operation.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch to ON and turn the intelligent tester main switch on.

        Note

        Do not start the engine.

      3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.

      4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

    2. Inspect for fuel leaks.


      1. Check for fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts if necessary.

    3. Turn the ignition switch off.

    4. Disconnect the intelligent tester from the DLC3.