ENGINE UNIT REASSEMBLY


  1. INSTALL CYLINDER HEAD GASKET

    A011A1Z

    1. Place a new cylinder head gasket on the cylinder block sub-assembly.

  2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

    Note

    Place the cylinder head gently in order not to damage the gasket.


    1. Place the cylinder head on the cylinder block sub-assembly.

    2. Install the 8 plate washers to the cylinder head sub-assembly.

      Note

      Do not drop the washers into the cylinder head.

    3. A011A31E01
      Text in Illustration
      *1 Apply Engine Oil.

      Apply engine oil to each bolt thread and seating surface.

    4. A01186HE01

      Using several passes, uniformly install and tighten the 8 cylinder head bolts with an 8 mm bi-hexagon wrench in the order shown in the illustration.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }
    5. A011AFFE02

      Mark the front of each cylinder head bolt with paint.

    6. Retighten the cylinder head bolts by additional 180° as shown in the illustration.

      Text in Illustration
      *1 Paint Mark

    7. Check that the paint mark are now 180° from the front.

  3. INSTALL VALVE LIFTER


    1. A01189S

      Apply engine oil to the circumference of the valve lifters.

    2. Install the valve lifters straight into the lifter holes.

      Note

      Check that the valve lifters turn smoothly after installing them.

  4. INSTALL ENGINE REAR OIL SEAL

    A01180QE01
    Text in Illustration
    *1 Apply Engine Oil.

    1. Apply engine oil to the lip of a new oil seal.

    2. Using SST, tap the oil seal straight in.

      A011A7TE01
      Text in Illustration
      *1 Rear Oil Seal Retainer - -
      SST
      09223-15020
      09950-70010   ( 09951-07200 )
      Correct oil seal position
      Protrusion from rear oil seal retainer edge
      0.5 mm (0.020 in.) or less
      Installation depth from rear oil seal retainer edge
      1.0 mm (0.039 in.) or less

  5. INSTALL ENGINE REAR OIL SEAL RETAINER

    A0117A6

    1. Install the stud bolt.

    2. A0116WTE01
      Text in Illustration
      *1 Seal Packing

      Apply a continuous bead of seal packing (Diameter 3 to 4 mm (0.12 to 0.16 in.)) as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    3. A0117BZ

      Install the oil seal retainer with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • Install the oil seal retainer within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

      • Do not add engine oil for at least 2 hours after installation.

      • Do not start the engine for at least 2 hours after installation.

  6. INSTALL CAMSHAFTS

    A011BJ3E01

    1. Before installing the camshaft, turn the crankshaft approximately 90° in the engine revolution direction from the point where the No. 1 piston is set at the TDC/ compression so that the lifted valve and piston do not touch each other.

    2. A01199RE01
      Text in Illustration
      *1 Apply Engine Oil.

      Apply engine oil to the contact areas of the cam and journal of the camshaft and No. 2 camshaft.

    3. A0118MWE02
      Text in Illustration
      *1 No. 1 Camshaft
      *2 No. 2 Camshaft
      *3 No. 3 Cylinder
      *4 No. 1 Cylinder
      *5 No. 2 Cylinder

      Install the camshafts as shown in the illustration.

    4. A0118QUE01

      Set the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps and tighten the bolts in the order shown in the illustration.

      Torque:
      No. 1 camshaft bearing cap
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }
      No. 2 camshaft bearing cap
      13 N*m  { 128 kgf*cm, 9 ft.*lbf }

      Note


      • Install the bearing caps with the front marks facing the engine front.

      • Install the bolts in the correct positions by referring to the numbers inscribed on the bolts and the table below.

      Installation Position of No. 2 Camshaft Bearing Cap
      Installation position Inscribed No.
      Intake No. 1 cylinder I2
      Intake No. 2 cylinder I3
      Intake No. 3 cylinder I4
      Exhaust No. 1 cylinder E2
      Exhaust No. 2 cylinder E3
      Exhaust No. 3 cylinder E4

  7. INSTALL CAMSHAFT TIMING GEAR OR SPROCKET


    1. Insert the camshaft timing gear or sprocket so that the knock pin on the No. 2 camshaft end fits into the groove.

    2. A011BF2E02

      While holding the hexagonal portion of the No. 2 camshaft, tighten the bolts to install the camshaft timing gear or sprocket.

      Torque:
      47 N*m  { 479 kgf*cm, 35 ft.*lbf }

  8. INSTALL CAMSHAFT TIMING SPROCKET ASSEMBLY

    A011AWRE01

    1. Apply engine oil to the camshaft timing sprocket installation portion of the camshaft.

      Text in Illustration
      *1 Apply Engine Oil.

    2. Insert the knock pin on the camshaft end into the knock hole in the camshaft timing sprocket.

      Note


      • Slightly turn the sprocket to make sure that the knock pin is securely installed after inserting the knock pin.

      • The end surface of the sprocket may be damaged if the sprocket is turned with excessive force when the knock pin is not inserted.

    3. A011B5AE02

      While holding the hexagonal portion of the camshaft, tighten the bolts to install the camshaft timing sprocket.

      Torque:
      47 N*m  { 479 kgf*cm, 35 ft.*lbf }

  9. INSPECT VALVE CLEARANCE

    A01183KE01
    Text in Illustration
    *1 Intake Side
    *2 Exhaust Side

    1. Check only the valves indicated.


      1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

        Valve clearance (Cold)
        Intake side
        0.145 to 0.235 mm (0.00571 to 0.00925 in.)
        Exhaust side
        0.275 to 0.365 mm (0.01083 to 0.01437 in.)

        Tech Tips

        Insert the feeler gauge from the spark plug side (center).

      2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.

    2. Turn the crankshaft 1 revolution (360°).

    3. A01196TE01
      Text in Illustration
      *1 Intake Side
      *2 Exhaust Side

      Check only the valves indicated.


      1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

        Valve clearance (Cold)
        Intake side
        0.145 to 0.235 mm (0.00571 to 0.00925 in.)
        Exhaust side
        0.275 to 0.365 mm (0.01083 to 0.01437 in.)

        Tech Tips

        Insert the feeler gauge from the spark plug side (center).

      2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.

  10. ADJUST VALVE CLEARANCE


    1. Remove the No. 1 and No. 2 camshafts Click here.

    2. Remove the valve lifters Click here.

    3. A011AP9

      Using a micrometer, measure the thickness of the removed valve lifters.

    4. Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.

      A Thickness of new lifter
      B Thickness of used lifter
      C Measured valve clearance
      Valve clearance
      Intake A = B + (C - 0.18 mm (0.0071 in.))
      Exhaust A = B + (C - 0.31 mm (0.0122 in.))

      Tech Tips


      • Select a new lifter with a thickness as close to the calculated values as possible.

      • Lifters are available in 29 sizes in increments of 0.020 mm (0.0008 in.), from 5.12 mm (0.2016 in.) to 5.68 mm (0.2236 in.).

      • Refer to the New Lifter Thickness Table on the next 2 pages.

    5. Install the valve lifters Click here.

    6. Install the No. 1 and No. 2 camshafts Click here.

      A011BOCE01
      A011BGGE02

      Tech Tips

      New Lifter Thickness mm (in.)
      Lifter No. Thickness Lifter No. Thickness Lifter No. Thickness
      12 5.12 (0.2016) 32 5.32 (0.2094) 52 5.52 (0.2173)
      14 5.14 (0.2024) 34 5.34 (0.2102) 54 5.54 (0.2181)
      16 5.16 (0.2031) 36 5.36 (0.2110) 56 5.56 (0.2189)
      18 5.18 (0.2039) 38 5.38 (0.2118) 58 5.58 (0.2197)
      20 5.20 (0.2047) 40 5.40 (0.2126) 60 5.60 (0.2205)
      22 5.22 (0.2055) 42 5.42 (0.2134) 62 5.62 (0.2213)
      24 5.24 (0.2063) 44 5.44 (0.2142) 64 5.64 (0.2220)
      26 5.26 (0.2071) 46 5.46 (0.2150) 66 5.66 (0.2228)
      28 5.28 (0.2079) 48 5.48 (0.2157) 68 5.68 (0.2236)
      30 5.30 (0.2087) 50 5.50 (0.2165) - -

  11. INSTALL CRANKSHAFT STRAIGHT PIN

    A0118TH

    1. Install the crankshaft straight pin into the crankshaft groove.

  12. INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

    A0117G3

    1. Align the groove of the crankshaft timing sprocket with the key of the crankshaft and install the crankshaft timing sprocket.

  13. INSTALL TIMING CHAIN GUIDE

    A0116WX

    1. Install the timing chain guide with the 2 bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  14. INSTALL CHAIN SUB-ASSEMBLY

    A011745E01
    Text in Illustration
    *1 Yellow Mark Plate
    *2 Timing Mark

    1. Align the yellow mark plate with the timing mark of the crankshaft timing sprocket and install the timing chain, as shown in the illustration.

    2. A0117I8E05
      Text in Illustration
      *1 Timing Mark
      *2 Orange Mark Plate

      Align the 2 orange mark plates with the timing marks of the camshaft timing sprockets and install the timing chain, as shown in the illustration.

  15. INSTALL TIMING CHAIN TENSION ARM

    A01177I

    1. Install the timing chain tension arm with the bolt.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  16. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

    A011992

    1. Slightly turn the hexagonal portion of the camshaft (intake side) counterclockwise to leave some slack on the chain of the timing chain tensioner side.

    2. A011752E01

      Install the No. 1 chain tensioner assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Remove the hexagon wrench, turn the crankshaft 2 complete revolutions and operate the chain tension assembly.

      Text in Illustration
      *1 Hexagon Wrench
    4. A011843E04
      Text in Illustration
      *1 Timing Mark

      Make sure that the timing mark of the sprocket camshaft timing is at the top with the timing chain tensed (set No. 1 piston to the TDC/ compression).

  17. INSTALL OIL PUMP GASKET

    A0117HO

    1. Install a new oil pump gasket onto the cylinder block.

  18. INSTALL VENTILATION CASE SUB-ASSEMBLY


    1. A01191S

      Install the ventilation case sub-assembly with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  19. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

    A011805E01

    1. Apply engine oil to the lip of a new oil seal.

      Text in Illustration
      *1 Apply Engine Oil.
    2. A0118LIE01

      Using SST, tap the oil seal straight in.

      SST
      09950-60010   ( 09951-00500, 09952-06010 )
      09950-70010   ( 09951-07200 )
      Correct oil seal position
      Protrusion from chain cover edge
      0.5 mm (0.020 in.) or less
      Installation depth from chain cover edge
      1.0 mm (0.039 in.) or less

  20. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


    1. Remove any oil packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover sub-assembly, cylinder head, and cylinder block.

    2. Apply seal packing as shown in the illustration.

      A0117DPE01
      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note


      • Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

      • Do not add engine oil for at least 2 hours after installation.

      • Do not start the engine for at least 2 hours after installation.

    3. A011BA2E01

      Temporarily install the timing chain cover sub-assembly with the 12 bolts.

      Bolt Length
      Item Length
      Bolt A 80 mm (3.15 in.)
      Bolt B 40 mm (1.57 in.)
      Bolt C 45 mm (1.77 in.)
      Bolt D 70 mm (2.78 in.)
      Bolt E 45 mm (1.77 in.)
    4. A0119NJ

      Install the new gasket to the timing chain cover sub-assembly.

    5. A0119ZEE01

      Temporarily install the oil filter bracket with the 2 bolts.

      Bolt Length
      Item Length
      Bolt A 20 mm (0.79 in.)
      Bolt B 119 mm (4.69 in.)
    6. A0119DF

      Install the new gasket to the timing chain cover sub-assembly.

    7. A0117OXE01

      Temporarily install the water pump assembly with 5 bolts.

      Bolt Length
      Item Length
      Bolt A 55 mm (2.17 in.)
      Bolt B 20 mm (0.79 in.)

    8. Fully tighten the timing chain cover sub-assembly with the 19 bolts as shown in the illustration.

      A0118GDE01
      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf, (Bolt A, C, E, F, G) }
      40 N*m  { 408 kgf*cm, 30 ft.*lbf, (Bolt B, D) }
      10 N*m  { 102 kgf*cm, 7 ft.*lbf, (Bolt H) }

      Note


      • Install the chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

      • Do not add engine oil for at least 2 hours after installation.

      • Do not start the engine for at least 2 hours after installation.

      Bolt Length
      Item Length
      Bolt A 80 mm (3.15 in.)
      Bolt B 40 mm (1.57 in.)
      Bolt C 45 mm (1.77 in.)
      Bolt D 70 mm (2.78 in.)
      Bolt E 55 mm (2.17 in.)
      Bolt F 20 mm (0.79 in.)
      Bolt G 119 mm (4.69 in.)
      Bolt H 45 mm (1.77 in.)

    9. Remove excess seal packing.

    10. A0118RK

      Install the 2 stud bolts.

  21. INSTALL TIMING GEAR COVER TIGHT PLUG

    A0119GQE01
    Text in Illustration
    *1 Seal Packing

    1. Clean the timing gear cover tight plug and installation surface of the timing chain cover.

    2. Apply a light coat of the seal packing black to the timing gear cover tight plug.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note


      • Install the timing gear tight plug within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

      • Do not add engine oil for at least 2 hours after installation.

      • Do not start the engine for at least 2 hours after installation.

    3. A0118F3E01
      Text in Illustration
      *1 8 mm Socket Hexagon Wrench

      Using an 8 mm socket hexagon wrench, install the timing gear cover tight plug onto the timing chain cover.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  22. INSTALL CRANKSHAFT PULLEY

    A011A50E01

    1. Align the pulley set key with the key groove of the pulley.

    2. Using SST, hold the pulley in place and tighten the bolt.

      SST
      09960-10010   ( 09962-01000, 09963-01000 )
      Torque:
      180 N*m  { 1836 kgf*cm, 133 ft.*lbf }

  23. INSTALL OIL FILTER SUB-ASSEMBLY

    A0117Y0E01

    1. Check and clean the oil filter installation surface.

    2. Apply clean engine oil to the gasket of a new oil filter.

    3. Gently screw the oil filter into place, and then tighten it until the gasket comes into contact with the seat.

    4. Using SST, tighten it an additional 3/4 turn.

      SST
      09228-06501

  24. INSTALL WATER INLET

    A0119Y1

    1. Install the water inlet with 2 nuts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  25. INSTALL NO. 1 WATER BY-PASS PIPE


    1. A0119TB

      Install a new gasket to the No. 1 water by-pass pipe.

    2. A011A3L

      Install a new gasket to the cylinder head.

    3. A011BAV

      Temporarily tighten the bolt and install the 2 nuts.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

    4. Fully tighten the bolt.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  26. INSTALL WATER VALVE


    1. A011AX7

      Install a new gasket to the water valve.

    2. Install the water valve with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  27. INSTALL OIL STRAINER SUB-ASSEMBLY

    A0118U4

    1. Install a new oil strainer gasket onto the oil strainer.

    2. A0118OY

      Install the oil strainer with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  28. INSTALL OIL PAN SUB-ASSEMBLY


    1. Remove any grease from the installation surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

    2. A0119NQE01

      Using a plastic hammer, tap into the straight pin, as shown in the illustration.

      Standard protrusion
      3 to 5 mm (0.11811 to 0.19685 in.)
    3. A011BBRE01
      Text in Illustration
      *1 Seal Packing
      *2 Contact surface between timing chain cover and cylinder block
      *3 Contact surface between oil seal retainer and cylinder block

      Apply seal packing to the oil pan sub-assembly and install it onto the cylinder block assembly.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.

      Note


      • Start and finish applying the seal packing on the seal surface with the cylinder block sub-assembly.

      • Apply seal packing to the contact surfaces between the timing chain cover and cylinder block, and between the oil seal retainer and cylinder block.

      • Install the oil pan sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

    4. A011ALGE01

      Tighten the specified 6 bolts in the order shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }
    5. A011BEDE01
      Text in Illustration
      *1 Nut
      *2 Bolt A
      *3 Bolt B

      Tighten the 6 bolts and 3 nuts.

      Torque:
      Nut and Bolt B
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      Bolt A
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  29. INSTALL OIL FILTER BRACKET STAY


    1. A01196P

      Install the oil filter bracket stay with 2 bolts.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  30. INSTALL OIL PAN DRAIN PLUG

    A011B26

    1. Install the engine oil drain plug with a new gasket.

      Torque:
      30 N*m  { 301 kgf*cm, 22 ft.*lbf }

  31. INSPECT VALVE CLEARANCE

  32. ADJUST VALVE CLEARANCE

  33. INSTALL VENTILATION VALVE SUB-ASSEMBLY

    A011BPQE01
    Text in Illustration
    *1 Grommet
    *2 Ventilation Valve Sub-Assembly

    1. Install the grommet, as shown in the illustration.

    2. Install the ventilation valve sub-assembly.

  34. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

    A011A1E

    1. Fit the cylinder head cover gasket into the groove on the cylinder head cover and onto the center bosses.

      Note

      Insert the gasket securely until it completely fits into the bosses.

    2. A011AO5E01

      Apply a continuous bead of seal packing (diameter: 3 to 4 mm (0.118 to 0.157 in.)) to the contact surface between the cylinder head assembly and timing chain cover assembly, as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note

      Install the cylinder head cover within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.

    3. A011B65E01
      Text in Illustration
      *1 Bolt A
      *2 Bolt B

      Tighten the bolts A, and then the bolts B.

      Torque:
      7.7 N*m  { 77 kgf*cm, 68 in.*lbf }

    4. Check once more that the bolts A meet the specified torque.

      Torque:
      7.7 N*m  { 77 kgf*cm, 68 in.*lbf }

  35. INSTALL OIL FILLER CAP SUB-ASSEMBLY

    A011B98

    1. Install a new gasket onto the oil filler cap.

    2. A01171C

      Install the oil filler cap.

  36. INSTALL OIL CONTROL VALVE FILTER

    A011BTEE01
    Text in Illustration
    *1 Oil Control Valve Filter
    *2 Gasket
    *3 Head Taper Screw Plug

    1. Install the oil control valve filter onto the head taper screw plug.

    2. A0116XEE01
      Text in Illustration
      *1 8 mm Hexagon Wrench

      Install a new gasket and install the oil control valve filter using an 8 mm hexagon wrench.

      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }

  37. INSTALL KNOCK CONTROL SENSOR


    1. A011BDCE01

      Install the knock control sensor with the bolt.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Position the knock control sensor as shown in the illustration.

  38. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


    1. A0116ZFE02
      Text in Illustration
      *1 Adhesive

      Apply adhesive to 2 or 3 threads of the oil pressure switch.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
    2. A0119YSE01
      Text in Illustration
      *1 24 mm Deep Socket Wrench

      Using a 24 mm deep socket wrench, install the oil pressure switch assembly.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Do not start the engine for at least 1 hour after installation.

  39. INSTALL CRANKSHAFT POSITION SENSOR

    A0117SE

    Note


    • Do not use parts that have been dropped or hit.

    • Make sure that the O-ring is not damaged before installing it.


    1. Apply a light coat of engine oil to the O-ring.

    2. Install the crankshaft position sensor with the bolt.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }

  40. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

    A011ATM

    Note

    Make sure that the O-ring is not damaged before installing it.


    1. Apply a light coat of engine oil to the O-ring.

    2. Install the camshaft timing oil control valve with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  41. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

    A0117STE01
    Text in Illustration
    *1 19 mm Deep Socket Wrench

    Note

    Do not use parts that have been dropped or hit.


    1. Install a new gasket onto the engine coolant temperature sensor.

    2. Using a 19 mm deep socket wrench, install the engine coolant temperature sensor.

      Torque:
      20 N*m  { 200 kgf*cm, 14 ft.*lbf }

  42. INSTALL CAMSHAFT POSITION SENSOR

    A011B2L

    Note


    • Do not use parts that have been dropped or hit.

    • Make sure that the O-ring is not damaged before installing it.


    1. Apply a light coat of engine oil to the O-ring.

    2. Install the camshaft position sensor with the bolt.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }

  43. INSTALL SPARK PLUG

    A011BON

    Note

    Do not use parts that have been dropped or hit.


    1. Install the 3 spark plugs.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  44. INSTALL ENGINE HANGERS

    A0118QB

    1. Install the 2 engine hangers with the 2 bolts.

      Torque:
      28 N*m  { 285 kgf*cm, 21 ft.*lbf }