ECD SYSTEM, Diagnostic DTC:P0489, P0490

DTC Code DTC Name
P0489 Exhaust Gas Recirculation Control Circuit Low
P0490 Exhaust Gas Recirculation Control Circuit High

DESCRIPTION

The ECM opens and closes the EGR valve using a DC motor type actuator. Due to opening and closing the valve, the exhaust gas recirculation volume can be properly controlled.

P0489
DTC Detection Drive Pattern DTC Detection Condition Trouble Area

Turn the ignition switch to ON and wait for 10 seconds

(Monitor this DTC only once per driving cycle)

Open in EGR valve circuit

(2 trip detection logic)

  • Electric EGR valve assembly

  • Open in EGR valve circuit

  • ECM
P0490
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine idling for 30 seconds

Short in EGR valve circuit

(2 trip detection logic)

  • Electric EGR valve assembly

  • Short in EGR valve circuit

  • ECM

WIRING DIAGRAM

A01180OE12

INSPECTION PROCEDURE

Note

When replacing the ECM, the ECM needs Registration and Initialization Click here.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the intelligent tester. Then after installing the new ECM, perform all of the initializations/registrations for the "Learning Values Write" function by following the instructions shown on the tester display.

  • Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / Actual EGR Valve Pos.

    4. When changing the Active Test value from 0 to 100%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.

      Standard Value
      Value smoothly changes to the set opening angle.

    OK

    CHECK WHETHER DTC OUTPUT RECURS (DTC P0489 OR P0490) Click here

    NG

    CHECK HARNESS AND CONNECTOR (ELECTRIC EGR VALVE ASSEMBLY - ECM) Click here

  2. CHECK HARNESS AND CONNECTOR (ELECTRIC EGR VALVE ASSEMBLY - ECM)


    1. A0119IUE02
      *1

      Front view of wire harness connector

      (to Electric EGR Valve Assembly)
      *2

      Front view of wire harness connector

      (to ECM)

      Disconnect the electric EGR valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      B9-23 (EGM+) - B50-1 (M+) Always Below 1 Ω
      B9-22 (EGM-) - B50-2 (M-) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      B9-23 (EGM+) or B50-1 (M+) - Body ground Always 10 kΩ or higher
      B9-22 (EGM-) or B50-2 (M-) - Body ground Always 10 kΩ or higher

    4. Reconnect the electric EGR valve assembly connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  3. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY


    1. Inspect the electric EGR valve assembly Click here.


    OK

    REPLACE ECM Click here

    NG

    REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY Click here

  4. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY


    1. Replace the electric EGR valve assembly Click here.

    2. Turn the ignition switch to ON.

    3. Turn the ignition switch off and wait for 30 seconds or more.


    NEXT

    CHECK WHETHER DTC OUTPUT RECURS (DTC P0489 OR P0490) Click here

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR


    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0489 OR P0490)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 10 seconds or more.

    6. Start the engine and wait for 30 seconds or more.

    7. Enter the following menus: Powertrain / Engine and ECT / DTC.

    8. Read the DTCs.

      Result
      Result Proceed to
      DTC P0489 or P0490 A
      No DTC output B

    B

    END

    A

  7. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 10 seconds or more.

    6. Start the engine and wait for 30 seconds or more.

    7. Enter the following menus: Powertrain / Engine and ECT / DTC.

    8. Confirm that the DTC is not output again.


    NEXT

    END