ECD SYSTEM REGISTRATION

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the intelligent tester. Then after installing the new ECM, perform all of the initializations/registrations for the "Learning Values Write" function by following the instructions shown on the tester display.

  • After replacing fuel injector(s), perform both the "Injector Compensation" and the "Pilot Quantity Learning Values Reset" functions using the intelligent tester. If fuel injector(s) and the ECM are replaced at the same time, perform the same initializations/registrations as when replacing the ECM.

  • After replacing the air fuel ratio sensor, perform the "A/F Sensor Compensation Reset" function using the intelligent tester. If the air fuel ratio sensor and the ECM are replaced at the same time, perform the same initializations/registrations as when replacing the ECM.

  • After replacing the DPF catalytic converter, perform the "DPF Deterioration Record Clear" function using the intelligent tester. If the DPF catalytic converter and the ECM are replaced at the same time, perform the same initializations/registrations as when replacing the ECM.

  • After replacing the engine assembly, perform both the "Injector Compensation" and the "Pilot Quantity Learning Values Reset" functions using the intelligent tester. If the engine assembly and the ECM are replaced at the same time, perform the same initializations/registrations as when replacing the ECM.

  • If the "Learning Values Save" or "Learning Values Write" function has failed, input manually the injection compensation codes and the vehicle mileage using the "Injector Compensation" and "Vehicle Mileage Write" functions by following the instructions shown on the intelligent tester display.

  • The items related to the DPF system appears on the intelligent tester display only for vehicles with the DPF system.


  1. LEARNING VALUES CONFIRMATION

    Tech Tips

    This function is used for reading a learning value(s) that is input correctly.

    A0119XKE01

    Tech Tips

    This process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning.

    A011AA4

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Confirmation.

    4. A011ARS

      Press "Next".

    5. A0119CM

      Press "Next".

      Tech Tips

      Confirm that the ignition switch is ON and the engine is stopped.

    6. A011BQH

      Select an item and press "Next".

    7. Confirm the compensation code or the learning value(s), that is selected.

      A0119FB

      Tech Tips


      • If you want to confirm other items continuously, press "Back" to return to the previous display.

      • To finish this function, press "Exit".

  2. LEARNING VALUES SAVE

    Tech Tips

    This function is used for saving data from the ECM to the intelligent tester depending on the replaced parts.

    A01182XE01

    Tech Tips

    This process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning.

    A0119TA

    Tech Tips

    If the ECM data cannot be read for some reason, input the vehicle mileage to a new ECM using the "Vehicle Mileage Write" function.

    A011AJH

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.

    4. A011919

      Press "Next".

    5. A0118E1

      Press "Next".

      Tech Tips

      Confirm that the ignition switch is ON and the engine is stopped.

    6. A011AIL
      A01179G

      Select item(s) for the replaced parts and press "Next".

      Tech Tips

      If the message appears for asking the data overwrite, press "Overwrite" to proceed to next step.

    7. A01178V

      Confirm the "Saved Date", and press "Exit" to finish this operation.

  3. LEARNING VALUES WRITE

    A0118MO

    Tech Tips

    This function is used for writing the saved data from the intelligent tester to the ECM.

    A011BBWE01

    Tech Tips

    This process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning.

    A011AUE

    Tech Tips

    If the saved data cannot be written into a new ECM for some reason, input the vehicle mileage to the ECM using the "Vehicle Mileage Write" function.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.

    4. A0118G6

      Press "Next".

      Tech Tips

      Confirm that the ignition switch is ON and the engine is stopped.

    5. A011A97

      Press "Next".

    6. A011BHK

      Confirm the "Saved Date", and press "Yes".

    7. A011BNF

      Confirm the displayed list of data settings that are completed.

    8. Press "Next".

    9. A01178E
      A011BOP

      Confirm the displayed list of data settings that need manual initialization and/or registration.

      Tech Tips

      If the message of "All settings are completed." Is displayed, press "Exit" to finish this operation.

  4. INJECTOR COMPENSATION

    A011AIZE01

    Note

    Injector compensation codes are 12-digit, alphanumeric values printed on the head of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    A011AU8E01

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

      Tech Tips

      Confirm that the ignition switch is ON and the engine is stopped.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.

    4. A0119DO

      Press "Next".

    5. A0117ZK

      Press "Next".

    6. A0118YU

      Press "Next".

    7. A0119XL

      Select the number of the cylinder corresponding to the injector compensation code that you want to input, and press "Next".

    8. Register the compensation code.


      1. A011AHR

        Press "Input".

      2. A011BNG

        Manually input the cylinder compensation code using the keyboard on the tester screen. The code is a 12-digit, alphanumeric value printed on the injector head.

        Tech Tips

        The compensation code for each selected cylinder must be input into the tester correctly.

      3. Confirm that the compensation code for the selected cylinder is correct, and then press OK.

    9. A011BIA

      Check that the compensation code displayed on the screen is correct by comparing it with the 12-digit alphanumeric value on the head of the fuel injector.

      Note

      If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

      Tech Tips


      • If a wrong compensation code is input or read, return to the Input Value screen by pressing Input.

      • The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning.

    10. Press Next to register the compensation code in the ECM.

      Tech Tips


      • If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

      • If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

    11. A01198H

      If you want to continue with other compensation code registrations, press "Next". To finish the registration, press "Exit".

    12. Turn the ignition switch off and turn the tester off.

    13. Wait for at least 30 seconds.

    14. Turn the ignition switch to ON and turn the tester on.

    15. Clear the DTC P0603 stored in the ECM using the tester.

  5. VEHICLE MILEAGE WRITE

    Tech Tips

    If Pilot Quantity Learning Values and DPF Deterioration Record cannot be saved or written using the intelligent tester, the ECM estimates the Pilot Quantity Learning Values and DPF Deterioration Record based on the traveled distance using this function.

    A01198ZE01

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Vehicle Mileage Write.

    4. A0119LM

      Press "Next".

    5. A011A74

      Press "Next".

      Tech Tips

      Confirm that the ignition switch is ON and the engine is stopped.

    6. A01192B

      Select item(s) for the replaced parts and press "Next".

      Tech Tips

      Multiple items can be selected. However the "Engine ECU" is always in the selected state and cannot be unselected.

    7. A01198G

      Check the actual vehicle mileage and select the adequate range, and press "Next".

    8. A011AVR

      Confirm the display and press "Next".

    9. A0119QE

      Press "Exit" to finish this operation.