NAME PLATE INSTALLATION


  1. INSTALL NO. 2 BACK DOOR NAME PLATE


    1. A0118POE01

      Clean the attachment surface.


      1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

        Tech Tips

        Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

      2. Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the No. 2 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Install a new No. 2 back door name plate as shown in the illustration.

      Installation Position
      Mark Measurement (along surface)
      *1 154 mm (6.063 in.)
      *2 81.1 mm (3.193 in.)
      *3 42.0 mm (1.654 in.)
      *4 83.0 mm (3.268 in.)

      Note

      Install the No. 2 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 back door name plate.

  2. INSTALL NO. 6 BACK DOOR NAME PLATE


    1. A0116ZBE01

      Clean the attachment surface.


      1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

        Tech Tips

        Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

      2. Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the No. 6 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Install a new No. 6 back door name plate as shown in the illustration.

      Installation Position
      Mark Measurement (along surface)
      *1 69.7 mm (2.744 in.)
      *2 66.3 mm (2.610 in.)
      *3 52.1 mm (2.051 in.)

      Note

      Install the No. 6 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 6 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 6 back door name plate.

  3. INSTALL NO. 1 BACK DOOR EMBLEM


    1. A01173DE01
      Text in Illustration
      *1 Location pin

      Clean the attachment surface.


      1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

        Tech Tips

        Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

      2. Using a piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the back door emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Insert the 2 pins into the back door panel and install the back door emblem.

      Note

      Install the back door emblem in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the back door emblem to 20 to 30°C (68 to 86°F) and install the back door emblem.

  4. INSTALL FRONT BUMPER EMBLEM


    1. A011AFPE01
      Text in Illustration
      *1 Location pin

      Clean the attachment surface.


      1. Using an infrared light, heat the double-sided adhesive tape remaining on the vehicle body.

        Tech Tips

        Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

      2. Using a piece of cloth, rub the remaining double-sided adhesive tape off the vehicle body while it is hot from the infrared light.

        Note

        Installing the front bumper emblem with any double-sided tape remaining on the engine hood may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Insert the 2 pins into the front bumper and install the front bumper emblem.

      Note

      Install the front bumper emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the front bumper emblem to 20 to 30°C (68 to 86°F) and install the front bumper emblem.