OUTER MIRROR SWITCH INSPECTION


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

    A011BH5E01
    Text in Illustration
    *1

    Component without harness connected

    (Outer Mirror Switch)

    1. Check the resistance.


      1. Select "L" on the left/right adjustment switch.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition

        4 (VL) - 8 (B)

        6 (M+) - 7 (E)

        		 UP Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        4 (VL) - 7 (E)

        6 (M+) - 8 (B)

        		 DOWN Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        5 (HL) - 8 (B)

        6 (M+) - 7 (E)

        		 LEFT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        5 (HL) - 7 (E)

        6 (M+) - 8 (B)

        		 RIGHT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch.

      3. Select "R" on the left/right adjustment switch.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition

        3 (VR) - 8 (B)

        6 (M+) - 7 (E)

        		 UP Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        3 (VR) - 7 (E)

        6 (M+) - 8 (B)

        		 DOWN Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        2 (HR) - 8 (B)

        6 (M+) - 7 (E)

        		 LEFT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        2 (HR) - 7 (E)

        6 (M+) - 8 (B)

        		 RIGHT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch.

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

    A0117EYE02
    Text in Illustration
    *1

    Component without harness connected

    (Outer Mirror Switch)

    1. Inspect the outer mirror switch.


      1. Select "L" on the left/right adjustment switch.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition

        4 (VL) - 8 (B)

        6 (M+) - 7 (E)

        		 UP Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        4 (VL) - 7 (E)

        6 (M+) - 8 (B)

        		 DOWN Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        5 (HL) - 8 (B)

        6 (M+) - 7 (E)

        		 LEFT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        5 (HL) - 7 (E)

        6 (M+) - 8 (B)

        		 RIGHT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch.

      3. Select "R" on the left/right adjustment switch.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition

        3 (VR) - 8 (B)

        6 (M+) - 7 (E)

        		 UP Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        3 (VR) - 7 (E)

        6 (M+) - 8 (B)

        		 DOWN Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        2 (HR) - 8 (B)

        6 (M+) - 7 (E)

        		 LEFT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        2 (HR) - 7 (E)

        6 (M+) - 8 (B)

        		 RIGHT Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch.

    2. Inspect the retract switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition

        7 (E) - 9 (MR)

        8 (B) - 10 (MF)

        Pressed

        (Retracts)

        		 Below 1 Ω
        Not pressed 10 kΩ or higher

        7 (E) - 10 (MF)

        8 (B) - 9 (MR)

        Pressed

        (Driving position)

        		 Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch.