OUTER REAR VIEW MIRROR INSPECTION


  1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

    A0119HKE01
    Text in Illustration
    *1

    Component without harness connected

    (Outer Rear View Mirror LH)

    1. Check the outer rear view mirror operation.


      1. Apply battery voltage and check the operation of the outer rear view mirror.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 1 (MV)

        Battery negative (-) → Terminal 2 (M+)

        		 Turns upward

        Battery positive (+) → Terminal 2 (M+)

        Battery negative (-) → Terminal 1 (MV)

        		 Turns downward

        Battery positive (+) → Terminal 3 (MH)

        Battery negative (-) → Terminal 2 (M+)

        		 Turns left

        Battery positive (+) → Terminal 2 (M+)

        Battery negative (-) → Terminal 3 (MH)

        		 Turns right

        If the result is not as specified, replace the outer rear view mirror.

    2. A011BJ7E01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror LH)

      w/ Mirror heater:

      Check the mirror heater.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester connection Condition Specified
        4 (+) - 9 (GND) 25°C (75°F) 8 to 11 Ω

        If the result is not as specified, replace the outer rear view mirror.

      2. Connect the cable from the negative battery (-) terminal to terminal 4 (+) and the positive battery (+) terminal to terminal 9 (GND). Then check that the mirror becomes warm.

        OK
        Mirror becomes warm.

        Tech Tips

        It takes a short time for the mirror to become warm.

        If the result is not as specified, replace the outer rear view mirror.

    3. A0118NNE01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror LH)

      Check the retractable mirror's movement.


      1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

        OK
        Measurement Condition Mirror Position Specified Condition

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Forward position (A) Moves from (A) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Forward position (A) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Driving position (C) Moves from (C) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Driving position (C) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Retracted position (E) Does not move

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Retracted position (E) Moves from (E) to driving position (C)

        Note


        • Disconnect and reconnect the battery between each mirror position check.


        • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

        If the result is not as specified, replace the mirror assembly.

  2. INSPECT OUTER MIRROR RETRACTOR LH (w/ Retract Mirror)


    1. A0118NNE01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror LH)

      Check the retractable mirror's movement.


      1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

        OK
        Measurement Condition Mirror Position Specified Condition

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Forward position (A) Moves from (A) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Forward position (A) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Driving position (C) Moves from (C) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Driving position (C) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Retracted position (E) Does not move

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Retracted position (E) Moves from (E) to driving position (C)

        Note


        • Disconnect and reconnect the battery between each mirror position check.


        • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

        If the result is not as specified, replace the outer mirror retractor.

  3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

    A0119CTE01
    Text in Illustration
    *1

    Component without harness connected

    (Outer Rear View Mirror RH)

    1. Check the outer rear view mirror operation.


      1. Apply battery voltage and check the operation of the outer rear view mirror.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 1 (MV)

        Battery negative (-) → Terminal 2 (M+)

        		 Turns upward

        Battery positive (+) → Terminal 2 (M+)

        Battery negative (-) → Terminal 1 (MV)

        		 Turns downward

        Battery positive (+) → Terminal 3 (MH)

        Battery negative (-) → Terminal 2 (M+)

        		 Turns left

        Battery positive (+) → Terminal 2 (M+)

        Battery negative (-) → Terminal 3 (MH)

        		 Turns right

        If the result is not as specified, replace the outer rear view mirror.

    2. A011ATOE01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror RH)

      Check the retractable mirror's movement.


      1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

        OK
        Measurement Condition Mirror Position Specified Condition

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Forward position (A) Moves from (A) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Forward position (A) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Driving position (C) Moves from (C) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Driving position (C) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Retracted position (E) Does not move

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Retracted position (E) Moves from (E) to driving position (C)

        Note


        • Disconnect and reconnect the battery between each mirror position check.


        • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

        If the result is not as specified, replace the mirror assembly.

    3. A011BO6E01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror RH)

      w/ Mirror heater:

      Check the mirror heater.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester connection Condition Specified Condition
        4 (+) - 9 (GND) 25°C (75°F) 8 to 11 Ω

        If the result is not as specified, replace the outer rear view mirror.

      2. Connect the cable from the negative battery (-) terminal to terminal 4 (+) and the positive battery (+) terminal to terminal 9 (GND). Then check that the mirror becomes warm.

        OK
        Mirror becomes warm.

        Tech Tips

        It takes a short time for the mirror to become warm.

        If the result is not as specified, replace the outer rear view mirror.

  4. INSPECT OUTER MIRROR RETRACTOR RH (w/ Retract Mirror)


    1. A011ATOE01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror RH)

      Check the retractable mirror's movement.


      1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

        OK
        Measurement Condition Mirror Position Specified Condition

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Forward position (A) Moves from (A) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Forward position (A) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Driving position (C) Moves from (C) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Driving position (C) Does not move

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)

        Battery positive (+) → Terminal 7 (MR)

        Battery negative (-) → Terminal 8 (MF)

        		 Retracted position (E) Does not move

        Battery positive (+) → Terminal 8 (MF)

        Battery negative (-) → Terminal 7 (MR)

        		 Retracted position (E) Moves from (E) to driving position (C)

        Note


        • Disconnect and reconnect the battery between each mirror position check.


        • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

        If the result is not as specified, replace the outer mirror retractor.