POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

If the AUTO UP/DOWN function does not operate, the cause may be one or more of the following:


WIRING DIAGRAM

A0117KFE01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuit related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK FOR DTC


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC is not output A
      B2311 is output B
      B2312 is output C
      B2313 is output D
      LIN communication system DTCs are output E

    B

    GO TO DTC (B2311) Click here

    C

    GO TO DTC (B2312) Click here

    D

    GO TO DTC (B2313) Click here

    E

    GO TO LIN COMMUNICATION SYSTEM Click here

    A

  2. CHECK MANUAL UP / DOWN FUNCTION


    1. Check that the manual UP/DOWN function using the power window regulator switch can operate the front passenger side door power window Click here.

      OK
      Manual UP/DOWN function operates.

    NG

    GO TO FLOW CHART (FRONT PASSENGER SIDE POWER WINDOW MOTOR CIRCUIT) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (P-DOOR MOTOR)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Body / P-Door Motor / Data List.

    5. According to the display on the tester, read the Data List.

      P-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Auto SW Front passenger side power window auto UP/DOWN switch signal / ON or OFF

      ON: Front passenger side power window auto UP/DOWN switch operated

      OFF: Front passenger side power window switch not operated

      		 -
      OK
      The tester display changes when front passenger side power window switch is operated.

    NG

    CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR) Click here

    OK

    REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR)


    1. A01177GE02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Power Window Regulator Switch Assembly)
      *2

      Front view of wire harness connector

      (to Front Power Window Regulator Motor Assembly)
      *3 for LHD
      *4 for RHD

      Disconnect the E2 or F2 power window regulator switch assembly connector.

    2. Disconnect the E4 or F4 front power window regulator motor assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E2-8 (AUTO) - E4-4 (AUTO) Always Below 1 Ω
      E2-8 (AUTO) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F2-8 (AUTO) - F4-4 (AUTO) Always Below 1 Ω
      F2-8 (AUTO) - Body ground Always 10 kΩ or higher

    4. Reconnect the front power window regulator motor assembly connector.

    5. Reconnect the power window regulator switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. A0118UGE03
      Text in Illustration
      *1

      Component without harness connected

      (Power Window Regulator Switch Assembly)

      Remove the power window regulator switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      8 (AUTO) - 1 (GND) AUTO UP/DOWN operation Below 1 Ω

    3. Reinstall the power window regulator switch assembly.


    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

    OK

    REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY Click here