POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION


WIRING DIAGRAM

A011ANFE01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuit related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK LIN COMMUNICATION SYSTEM


    1. Check for LIN communication system DTCs related to the power window control system Click here.

      OK
      LIN communication system DTCs are not output.

    NG

    GO TO LIN COMMUNICATION SYSTEM Click here

    OK

  2. CHECK FOR DTC (B2312)


    1. Check if DTC B2312 is output Click here.

      OK
      DTC B2312 is not output.

    NG

    GO TO DTC (B2312) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (P-DOOR MOTOR)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Body / P-Door Motor / Data List.

    5. According to the display on the tester, read the Data List.

      P-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Up SW Front passenger side power window manual UP switch signal / ON or OFF

      ON: Front passenger side power window manual UP switch operated

      OFF: Front passenger side power window switch not operated

      		 -
      P Door P/W Down SW Front passenger side power window manual DOWN switch signal / ON or OFF

      ON: Front passenger side power window manual DOWN switch operated

      OFF: Front passenger side power window switch not operated

      		 -
      OK
      The tester display changes normally when front passenger side power window switch is operated.

    NG

    CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BODY GROUND) Click here

    OK

    REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BODY GROUND)


    1. A0117ROE02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Power Window Regulator Switch Assembly)
      *2 for LHD
      *3 for RHD

      Disconnect the E2 or F2 power window regulator switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E2-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      F2-1 (GND) - Body ground Always Below 1 Ω

    3. Reconnect the power window regulator switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - BATTERY, BODY GROUND)


    1. A0118W5E02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Front Power Window Regulator Motor Assembly)
      *2 for LHD
      *3 for RHD

      Disconnect the E4 or F4 front power window regulator motor assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      E4-2 (B) - Body ground Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      F4-2 (B) - Body ground Always 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E4-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      F4-1 (GND) - Body ground Always Below 1 Ω

    4. Reconnect the front power window regulator motor assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR)


    1. A01177GE01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Power Window Regulator Switch Assembly)
      *2

      Front view of wire harness connector

      (to Front Power Window Regulator Motor Assembly)
      *3 for LHD
      *4 for RHD

      Disconnect the E2 or F2 front power window regulator switch assembly connector.

    2. Disconnect the E4 or F4 front power window regulator motor assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E2-6 (UP) - E4-10 (UP) Always Below 1 Ω
      E2-7 (DOWN) - E4-7 (DOWN) Always Below 1 Ω
      E2-6 (UP) - Body ground Always 10 kΩ or higher
      E2-7 (DOWN) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F2-6 (UP) - F4-10 (UP) Always Below 1 Ω
      F2-7 (DOWN) - F4-7 (DOWN) Always Below 1 Ω
      F2-6 (UP) - Body ground Always 10 kΩ or higher
      F2-7 (DOWN) - Body ground Always 10 kΩ or higher

    4. Reconnect the front power window regulator motor assembly connector.

    5. Reconnect the front power window regulator switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. A0118UGE02
      Text in Illustration
      *1

      Component without harness connected

      (Power Window Regulator Switch Assembly)

      Remove the power window regulator switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      6 (UP) - 1 (GND) MANUAL UP operation Below 1 Ω
      7 (DOWN) - 1 (GND) MANUAL DOWN operation Below 1 Ω

    3. Reinstall the power window regulator switch assembly.


    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

    OK

    REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY Click here