ROOF HEADLINING REMOVAL


  1. REMOVE REAR SEAT ASSEMBLY

    Click here

  2. REMOVE REAR FLOOR BOARD SUB-ASSEMBLY (w/o Rear Seat Assembly)


    1. A011AQP

      Remove the 6 bolts and rear floor board.

  3. REMOVE FRONT DOOR SCUFF PLATE RH


    1. A011AJ3

      Disengage the 9 claws and remove the front door scuff plate.

  4. REMOVE FRONT DOOR SCUFF PLATE LH

    Tech Tips

    Use the same procedure as for the RH side.

  5. REMOVE COWL SIDE TRIM BOARD RH


    1. A0117YC

      Disengage the 2 claws and the guide and remove the cowl side trim board.

  6. REMOVE COWL SIDE TRIM BOARD LH

    Tech Tips

    Use the same procedure as for the RH side.

  7. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  8. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  9. REMOVE REAR DECK TRIM COVER


    1. A0116Z2

      Remove the 2 clips.

    2. Disengage the 6 claws and remove the rear deck trim cover.

  10. REMOVE DECK TRIM SIDE BELT HOLE COVER RH


    1. A011AN1

      Disengage the 5 claws and remove the deck trim side belt hole cover.

  11. REMOVE DECK TRIM SIDE BELT HOLE COVER LH

    Tech Tips

    Use the same procedure as for the RH side.

  12. REMOVE SIDE NO. 1 TRIM ASSEMBLY RH


    1. A0119QR

      Disengage the 6 clips and remove the side No. 1 trim.

  13. REMOVE SIDE NO. 1 TRIM ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  14. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH


    1. A0119FW

      Remove the bolt and separate the front seat outer belt.

  15. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  16. REMOVE CENTER PILLAR UPPER GARNISH RH


    1. A011BPG

      Remove the 2 clips.

    2. Disengage the 4 clips.

    3. Pass the front seat outer belt through the slit in the center pillar upper garnish and remove the center pillar upper garnish.

    4. Remove the 3 clip caps from the body side.

  17. REMOVE CENTER PILLAR UPPER GARNISH LH

    Tech Tips

    Use the same procedure as for the RH side.

  18. SEPARATE REAR SEAT OUTER BELT ASSEMBLY RH


    1. A0118Q7E02
      Text in Illustration
      *a Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the rear seat belt anchor cover.

    2. A0119RL

      Remove the bolt and separate the rear seat outer belt.

  19. SEPARATE REAR SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  20. REMOVE ROOF SIDE INNER GARNISH RH


    1. A011AYB

      Disengage the 3 clips and remove the roof side inner garnish.

  21. REMOVE ROOF SIDE INNER GARNISH LH

    Tech Tips

    Use the same procedure as for the RH side.

  22. REMOVE PERSONAL LIGHT ASSEMBLY

    A01173J

    1. Using a roof moulding remover, disengage the claw.

    2. Disconnect the connector, and remove the personal light.

  23. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

    Click here

  24. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

    Click here

  25. REMOVE RAIN SENSOR

    Click here

  26. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

    Note

    Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.


    1. A0117TFE02
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Using a moulding remover, disengage the front pillar garnish clip and the clip.

      Tech Tips

      The front pillar garnish clip should remain between the front pillar garnish and the front pillar.

    2. A01179QE03
      Text in Illustration
      *a Protective Tape

      Using needle nose pliers with their tips wrapped in protective tape, turn the front pillar garnish clip 90° and disengage it from the front pillar garnish.

      Note


      • As a front pillar garnish clip is reusable, do not remove it from the front pillar as long as it is not damaged.

      • If the front pillar garnish clip is removed, replace it with a new one.

    3. Disengage the 2 guides and remove the front pillar garnish.

    4. A011AH5

      Disconnect the connector.

    5. Disengage the 2 clamps.

    6. A011BIDE03
      Text in Illustration
      *a Protective Cover
      *b Adhesive Tape

      Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the protective cover with adhesive tape, as shown in the illustration.

      Protective Cover Size
      Area Dimension
      a 700 mm (2.3 ft.)
      b 120 mm (4.72 in.)

  27. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure as for the RH side.

  28. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)


    1. A01179N

      Disengage the 2 clips and the 2 guides and remove the front pillar garnish.

    2. A011AH5

      Disconnect the connector.

    3. Disengage the 2 clamps.

  29. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure as for the RH side.

  30. REMOVE ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure to remove all assist grips.


    1. A011AFLE07
      Text in Illustration
      *a Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip cover.

      Tech Tips

      Use the same procedure for both sides.

    2. A01184Z

      Disengage the 2 clips and remove the assist grip.

  31. REMOVE VISOR ASSEMBLY RH


    1. A0118SZE07
      Text in Illustration
      *a Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor cover.

    2. A01173L

      Remove the visor shaft from the visor holder.

    3. Disengage the 2 clips and remove the visor.

  32. REMOVE VISOR ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  33. REMOVE VISOR HOLDER RH


    1. A011B3KE01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

  34. REMOVE VISOR HOLDER LH

    Tech Tips

    Use the same procedure as for the RH side.

  35. REMOVE ROOF HEADLINING ASSEMBLY


    1. A0117C1

      Disconnect the 2 connectors.

    2. Remove the bolt and the bracket.

    3. A0118OG

      Remove the 2 clips.

      Note


      • Pull the center of the clip straight down, and do not pull it all the way through the hole.

      • The clips will be damaged if twisted with a moulding remover.

    4. A0119ZZ

      Remove the roof headlining from the front door.

  36. REMOVE GARNISH MALE RETAINER SUB-ASSEMBLY


    1. A01175J

      Remove the 2 garnish male retainers.

  37. REMOVE ROOF HEADLINING CLIP

    Tech Tips

    Use the same procedure for both sides.


    1. A0118O6

      Disengage the 2 claws and remove the roof headlining clip.

  38. REMOVE NO. 1 ROOF SILENCER PAD


    1. Remove the 3 No. 1 roof silencer pads.

      A011AY4

  39. REMOVE ROOF WIRE


    1. A0118BT

      Remove the 8 pieces of tape.

    2. Remove the roof wire from the roof headlining.

  40. REMOVE ROOF HEADLINING PAD (w/o Rear Seat Assembly)


    1. A011751

      Remove the 2 roof headlining pads.

  41. REMOVE ANTENNA CORD SUB-ASSEMBLY

    A011ABR

    1. Remove the 6 pieces of tape.

    2. Remove the antenna cord from the roof headlining.