REAR DOOR BELT MOULDING (for Wagon) INSTALLATION

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.


  1. INSTALL REAR DOOR BELT MOULDING LH

    A00OTXL

    1. Attach the 7 claws to install the rear door belt moulding.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A00OQPG

      Install the front side of the glass run.

    2. A00OV87E01

      Apply MP grease to the sliding areas of the glass channel as shown in the illustration.

      Standard
      Area Specified Condition
      A 130 mm (5.12 in.)
      B 29 mm (1.14 in.)
    3. A00ORRB

      Slide the rear door glass sub-assembly as shown in the illustration to install it.

  3. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A00OV1OE01

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A00OS4T

      Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door window division bar sub-assembly to the glass run.

    3. A00OUN7E01

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

      Torque:
      6.2 N*m  { 63 kgf*cm, 55 in.*lbf, for bolt and screw }

  5. INSTALL REAR DOOR GLASS RUN LH


    1. A00OTWXE01

      Completely install the glass run.

  6. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply butyl tape to the door.

    2. A00OS24E01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

      Note


      • When installing the service hole cover, pull the links and connectors through the service hole cover.

      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the seal quality.

    3. Attach the rear door service hole cover by using the reference points on the rear door panel.

    4. Connect the connector.

  7. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A00OQSY

      Install the rear door inner glass weatherstrip to the door panel.

  8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00OU2R

      Connect the 2 cables to the inside handle.

    2. for 11 Speakers:

      Connect the connector.

    3. A00OSZBE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Attach the rear door trim board with the 4 claws on the rear door inner glass weatherstrip.

    4. A00OV40

      Install the rear door trim board with the 8 clips.

    5. Install the 3 screws.

  9. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)


    1. Connect the connector.

    2. A00OVNC

      Attach the 6 claws and clip to install the rear power window regulator switch assembly with rear door armrest base panel.

  10. INSTALL DOOR ASSIST GRIP COVER LH


    1. A00ORVS

      Attach the 10 claws to install the door assist grip cover.

  11. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A00OUXU

      Attach the 3 claws to install the rear door inside handle bezel plug.

  12. INSTALL REAR DOOR NO. 1 STIFFENER CUSHION


    1. A00ORCD

      Install the rear door No. 1 stiffener cushion.

  13. INSTALL REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Install the rear door regulator inside handle plate.

  14. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. Temporarily install the rear door window regulator handle assembly and fully open the window.

    2. Install the snap ring to the rear door window regulator handle assembly.

    3. A00ORY7E02
      Text in Illustration
      *1 Front Side

      Install the rear door window regulator handle assembly as shown in the illustration.

      Standard
      Area Specified Condition
      A 2.4° to 22.4°

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.