HOOD LOCK CONTROL CABLE ASSEMBLY INSTALLATION

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. A00OJD7E02
      Text in Illustration
      *1 String

      Tie the string passed through the engine compartment to the end of the hood lock control cable assembly as shown in the illustration.

    2. Pull the string until the hood lock control cable grommet contacts the dash panel, and then connect the clamps shown in the illustration to install the cable.

      A00OHQZE01
      Text in Illustration
      *1 Hood Lock Control Cable *6 Apron
      *2 Clamp *7

      w/ Rear Wiper:

      Rear Washer Hose

      *3 Bypass Hose *8 Grommet
      *4 Radiator Support Side *9 Hood Lock Control Cable Grommet
      *5 Fender Liner *10 Plug Hole
    3. A00OI4WE01
      Text in Illustration
      *1 Hood Lock Control Cable
      *2 String
      *3 Dash to Frame Brace
      *4 Engine Room Main Wire
      *5 Instrument Panel Wire
      *6 Hood Lock Control Cable Grommet
      *7 Floor Wire

      After pulling the end of the hood lock control cable assembly into the cabin as shown in the illustration, remove the string.

  2. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. A00OJD7E02
      Text in Illustration
      *1 String

      Tie the string passed through the engine compartment to the end of the hood lock control cable assembly as shown in the illustration.

    2. Pull the string until the hood lock control cable grommet contacts the dash panel, and then connect the clamps shown in the illustration to install the cable.

      A00OJUUE01
      Text in Illustration
      *1 Hood Lock Control Cable *7 Fender Liner
      *2 Clamp *8 Apron
      *3 Clamp *9

      w/ Rear Wiper:

      Rear Washer Hose

      *4 Bypass Hose *10 Grommet
      *5 Radiator Support *11 Hood Lock Control Cable Grommet
      *6 Radiator Support Side *12 Plug Hole
    3. A00OJBCE01
      Text in Illustration
      *1 Hood Lock Control Cable
      *2 String
      *3 Dash to Frame Brace
      *4 Engine Room Main Wire
      *5 Instrument Panel Wire
      *6 Hood Lock Control Cable Grommet

      After pulling the end of the hood lock control cable assembly into the cabin as shown in the illustration, remove the string.

  3. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A00OJGA

      Connect the hood lock control cable assembly.

    2. Attach the 3 claws to install the hood lock control lever sub-assembly.

  4. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A00OV6B

      Attach the guide.

    2. Connect the connectors.

    3. A00ORBF

      Attach the claw to install the under cover.

    4. Install the 2 screws <A>.

  5. INSTALL HOOD LOCK ASSEMBLY


    1. A00OM35

      Apply MP grease to the sliding areas of the lock.

    2. A00ONX5E01

      Connect the hood lock control cable.

    3. Install the 3 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
    4. w/ Engine Hood Courtesy Switch:

      Connect the connector.

  6. INSTALL FRONT FENDER LINER LH


    1. A003E2G

      Attach the 8 clips to install the front fender liner LH.

    2. Attach 5 new grommets.

    3. A003CAP

      Install the 6 screws.

    4. A003B86

      Install the pin hold clip.

  7. INSTALL RADIATOR SUPPORT OPENING COVER


    1. Install the radiator support opening cover with the 7 clips.

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.