SEAT HEATER SWITCH REMOVAL

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00EB81E01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  2. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00E7QBE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  3. REMOVE NO. 3 BOX PANEL


    1. Place protective tape as shown in the illustration.

      A006SZ5E02
      Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  4. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00E7Y2E01

  5. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00E70T

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  6. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00E8WSE01

  7. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    1. A006VX0

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  8. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)


    1. A006SXK

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  9. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)


    1. A006VCT

      Detach the cover.

    2. A006VV0

      Using a moulding remover B, detach the 2 claws.

    3. Detach the 6 clips and remove the console panel.

  10. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transaxle)


    1. A006UW6

      Using a moulding remover B, detach the 2 claws.

    2. Detach the 6 clips.

    3. Remove the console panel and then disconnect the connector.

  11. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL


    1. A006SNF

      Using a moulding remover B, detach the 2 clips.

    2. A006UTXE01
      Text in Illustration
      *1 w/ Seat Heater System

      Remove the finish panel and then disconnect the connectors.

  12. REMOVE SEAT HEATER SWITCH (for LH Side)


    1. A006WDY

      Detach the 2 claws and remove the switch.

  13. REMOVE SEAT HEATER SWITCH (for RH Side)


    1. A006T3K

      Detach the 2 claws and remove the switch.