LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Power Seat) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE FRONT SEAT ASSEMBLY

    Click here

  2. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A00OMTGE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape around the front seat cushion shield LH.

    2. Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A00OHTYE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the slide and vertical power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. A00OLOL

      Detach the 2 rubber bands.

    2. A00OIUO

      Remove the 2 screws and detach the 2 claws.

    3. A00OIYK

      Remove the 2 screws.

    4. Pull the front seat cushion shield LH to detach the hook and remove the front seat cushion shield LH with front seat No. 1 inner cushion shield.

    5. A00OMVA

      for Driver Side:

      Disconnect the connector.

  5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH


    1. A00OMPQE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Pull the front seat inner cushion shield LH to detach the hook and remove it.

    3. Detach the wire harness clamp.

  6. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. Detach the 2 hooks.

      A00OLNR
    2. A00OILD

      Detach the 2 hooks from the bottom of the separate type front seatback cover.

    3. A00OM19

      Detach the 2 hooks and disconnect the 2 straps.

    4. A00ONU5

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the surface.

    5. A00OIU0E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the screw and detach the seatback cover bracket.

    6. A00OME0E01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog rings and detach the 3 hooks from the center of the separate type front seatback pad.

    7. A00OIBR

      Detach the 7 hooks and remove the actuator shield.

    8. A00ONV8E01
      Text in Illustration
      *1 Cable End
      A00OMA6 Pull

      Pull the cable to loosen it, and then disconnect the cable end from the active headrest lower unit.

    9. A00OJIH

      Detach the 2 claws and remove the active headrest lower unit.

    10. A00OLW6

      Using a screwdriver, detach the 2 claws and disconnect the cable.

    11. A00OKVCE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog ring and detach the 2 hooks and open the seatback mat.

    12. A00OI4E

      Cut off the cable tie.

    13. A00OKRGE01
      Text in Illustration
      *1 Cable End

      Push the cable to push out the cable end from the clip.

    14. A00OJDI

      Detach the 2 claws and remove the clip.

    15. A00OHQJ

      Pull the cable through the hole of the seatback frame.

    16. A00OMD2E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    17. A00OIA8

      Detach the 2 claws and remove the 2 front seat headrest supports.

    18. A00ONM4

      Detach the 2 hooks and remove the separate type front seatback cover.

  7. REMOVE SEPARATE TYPE FRONT SEATBACK PAD


    1. A00ON5J

      Disconnect the connector.

    2. A00OJNW

      Remove the separate type front seatback pad.

  8. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. A00OLJ2

      Disconnect the connector.

    2. A00ONVL

      Detach the 8 hooks and remove the seatback spring.

    3. A00ONFCE01
      Text in Illustration
      *1 Back Sheet

      Pull the wire harness and disconnect it from the 2 back sheets as shown in the illustration.

    4. A00OIAPE01
      Text in Illustration
      *1 Back Sheet
      *2 Hook A
      *3 Hook B
      *4 Cable Tie

      Detach the 4 hooks A and fold back the 2 back sheets.

    5. Cut off the 2 cable ties, detach the 2 hooks B, and then remove the lumbar support adjuster assembly LH from the seatback spring.