LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Manual Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    A00OJ4JE01

    1. Attach the 2 hooks B to install the lumbar support adjuster assembly LH to the seatback spring.

      Text in Illustration
      *1 Back Sheet
      *2 Hook A
      *3 Hook B
      *4 Cable Tie

    2. Install 2 new cable ties.

    3. Return the 2 back sheets to their original positions and attach the 4 hooks A.

    4. A00OM9P

      Return the wire harness to its original position as shown in the illustration.

    5. A00OLVO

      Attach the 8 hooks to install the seatback spring.

    6. A00ON1B

      Connect the connector.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. A00OMMP

      Install the separate type front seatback pad.

    2. A00OKVM

      w/ Seat Heater System:

      Connect the connector.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A00OU67

      Attach the 2 hooks.

    2. A00OU1V

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. A00OS92

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    4. A00OS4B

      Pass the cable through the hole of the seatback frame.

    5. A00OUDV

      Attach the 2 claws to install the clip.

    6. A00OR0OE01
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    7. A00OTVM

      Install a new cable tie.

    8. A00OULRE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks to close the seatback mat.

    9. A00OUU1

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    10. Using hog ring pliers, install a new hog ring.

    11. A00OU7N

      Attach the 2 claws to install the active headrest lower unit.

    12. A00OS77E01
      Text in Illustration
      *1 Cable End
      A00OV9Z Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    13. A00OVHM

      Attach the 7 hooks to install the actuator shield.

    14. A00OVKNE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    15. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    16. A00OSOGE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    17. A00OSRY

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    18. A00OUJ0

      Attach the 2 hooks to connect the 2 straps.

    19. A00OU2U

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    20. Attach the 2 hooks.

      A00OVXG

  4. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A00ORGDE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  5. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A00OV7P

      w/ Lumbar Support:

      Connect the connector.

    2. A00OU31

      Attach the claw and hook to install the front seat cushion shield LH.

    3. Install the 2 screws.

    4. A00OUW4

      Attach the 2 rubber bands.

  6. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A00OTKH

      Attach the claw to install the reclining adjuster release handle LH.

  7. INSTALL VERTICAL ADJUSTING HANDLE LH


    1. A00OT5S

      Install the vertical adjusting handle LH with the 2 screws.

  8. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP


    1. A00OV1V

      Attach the 3 claws to install the vertical seat adjuster knob cap.

  9. INSTALL FRONT SEAT ASSEMBLY

    Click here

  10. CHECK SRS WARNING LIGHT

    Click here

  11. INSPECT FRONT SEAT ASSEMBLY


    1. Check the lumbar support operation.


      1. Operate the lumbar front power seat switch and check that the lumbar support moves in both directions.

    2. w/ Seat Heater System:

      Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.