LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Manual Seat) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE FRONT SEAT ASSEMBLY

    Click here

  2. REMOVE VERTICAL SEAT ADJUSTER KNOB CAP


    1. A00OVI7E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the vertical seat adjuster knob cap.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE VERTICAL ADJUSTING HANDLE LH


    1. A00OT5S

      Remove the 2 screws and vertical adjusting handle LH.

  4. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


    1. A00OSHWE01
      Text in Illustration
      *1 Protective Tape

      Raise the reclining adjuster release handle LH to reveal the claw. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. A00OR3W

      Detach the 2 rubber bands.

    2. A00OUTV

      Remove the 2 screws.

    3. Detach the hook and claw and remove the front seat cushion shield LH.

    4. A00OV7P

      w/ Lumbar Support:

      Disconnect the connector.

  6. REMOVE FRONT SEAT INNER CUSHION SHIELD LH


    1. A00OSH0E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Detach the hook and wire harness clamp and remove the front seat inner cushion shield LH.

  7. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. Detach the 2 hooks.

      A00OTPF
    2. A00OU2U

      Detach the 2 hooks from the bottom of the separate type front seatback cover.

    3. A00OSE1

      Detach the 2 hooks and disconnect the 2 straps.

    4. A00OSH3

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the surface.

    5. A00OSOGE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the screw and detach the seatback cover bracket.

    6. A00OUE7E01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog rings and detach the 3 hooks from the center of the separate type front seatback pad.

    7. A00OVHM

      Detach the 7 hooks and remove the actuator shield.

    8. A00OTQXE01
      Text in Illustration
      *1 Cable End
      A00OVAR Pull

      Pull the cable to loosen it, and then disconnect the cable end from the active headrest lower unit.

    9. A00OUWJ

      Detach the 2 claws and remove the active headrest lower unit.

    10. A00OUU1

      Using a screwdriver, detach the 2 claws and disconnect the cable.

    11. A00OURQE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog ring and detach the 2 hooks and open the seatback mat.

    12. A00OTVM

      Cut off the cable tie.

    13. A00OVSTE01
      Text in Illustration
      *1 Cable End

      Push the cable to push out the cable end from the clip.

    14. A00OUDV

      Detach the 2 claws and remove the clip.

    15. A00ORP6

      Pull the cable through the hole of the seatback frame.

    16. A00OROIE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    17. A00OV0Q

      Detach the 2 claws and remove the 2 front seat headrest supports.

    18. A00OU67

      Detach the 2 hooks and remove the separate type front seatback cover.

  8. REMOVE SEPARATE TYPE FRONT SEATBACK PAD


    1. A00OKVM

      w/ Seat Heater System:

      Disconnect the connector.

    2. A00OJNW

      Remove the separate type front seatback pad.

  9. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. A00ON1B

      Disconnect the connector.

    2. A00OLVO

      Detach the 8 hooks and remove the seatback spring.

    3. A00ONFCE01
      Text in Illustration
      *1 Back Sheet

      Pull the wire harness and disconnect it from the 2 back sheets as shown in the illustration.

    4. A00OIAPE01
      Text in Illustration
      *1 Back Sheet
      *2 Hook A
      *3 Hook B
      *4 Cable Tie

      Detach the 4 hooks A and fold back the 2 back sheets.

    5. Cut off the 2 cable ties, detach the 2 hooks B, and then remove the lumbar support adjuster assembly LH from the seatback spring.