FRONT SEAT CUSHION HEATER (for Manual Seat) INSTALLATION

Note

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH


    1. Remove the peeling paper from a new cushion heater.

    2. A003C0C

      Install the cushion heater to a new front seat cushion pad.

  2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A010GGQ

      Attach the hooks to install the cover.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A010LAP

    2. w/ Seat Heater System:

      Connect the connector.

    3. A010MAE

      w/ Lumbar Support:

      Attach the wire harness clamp.

    4. for Passenger Side:


      1. A010LZM

        Attach the 2 hooks to install the connector holder.

    5. w/ Seat Heater System:


      1. A010J4I

        Connect the connector.

      2. A010GDU

        Install a new cable tie.

    6. A010LVJ

      Attach the 2 rubber bands.

    7. for Driver Side:


      1. A010IVG

        Attach the 2 claws to install the vertical adjuster handle bracket with connector link.

      2. A010JUA

        Install the connector link and attach the clip.

    8. A010M6T

      Install the reclining handle with the nut.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
    9. A010K9Z

      Attach the 2 hooks to install the spring.

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Tech Tips


    • Use the same procedure for the RH and LH sides.

    • The procedure listed below is for the LH side.


    1. A003EE0E01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

  5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A010FYQE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the shield.

    2. Install the 2 screws.

  6. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A010I8D

      w/ Lumbar Support:

      Connect the connector.

    2. A010INS

      Attach the claw and hook to install the cushion shield.

    3. Install the 2 screws.

  7. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A010KI5

      Attach the claw to install the release handle.

  8. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    1. A010LKH

      Install the handle with the 2 screws.

  9. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. A010IM5

      Attach the 2 claws to install the cap.

  10. INSTALL FRONT SEAT ASSEMBLY


    1. Install the front seat assembly Click here.

  11. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  12. INSPECT FRONT SEAT ASSEMBLY


    1. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch ON.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.