FRONT POWER SEAT MOTOR ASSEMBLY (for Rear Lifter) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE FRONT SEAT ASSEMBLY

    Click here

  2. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A00OMTGE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape around the front seat cushion shield LH.

    2. Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A00OHTYE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the slide and vertical power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD


    1. A00OLOL

      Detach the 2 rubber bands.

    2. A00OIUO

      Remove the 2 screws and detach the 2 claws.

    3. A00OIYK

      Remove the 2 screws.

    4. Pull the front seat cushion shield LH to detach the hook and remove the front seat cushion shield LH with front seat No. 1 inner cushion shield.

    5. A00OMVA

      for Driver Side:

      Disconnect the connector.

  5. REMOVE FRONT POWER SEAT SWITCH


    1. A00OM6W

      Disconnect the connector.

    2. Remove the 3 screws and front power seat switch.

  6. REMOVE FRONT SEAT INNER CUSHION SHIELD LH


    1. A00OMPQE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Pull the front seat inner cushion shield LH to detach the hook and remove it.

    3. Detach the wire harness clamp.

  7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. for Driver Side:

      Disconnect the connector and detach the clamps.

    2. for Passenger Side:

      Disconnect the connectors and detach the clamps.

    3. A003CGA

      Remove the nut and front seat inner belt.

  8. REMOVE SEAT CUSHION COVER WITH PAD


    1. A00OI8F

      Disconnect the connector.

    2. A00ONI3

      Cut off the cable tie.

    3. A00OLIT

      for Front Passenger Side:

      Detach the 2 hooks and disconnect the connector holder.

    4. A00OKBS

      for Driver Side:

      Detach the wire harness clamp.

    5. Disconnect the 2 connectors.

      A00OKFL
    6. Detach the hooks and remove the seat cushion cover with pad.

  9. REMOVE POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)


    1. Put a 4 mm (0.157 in.) drill bit into a drill.

    2. A00ONA2E01

      Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

      Tech Tips

      Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. A00OKQW

      Lightly press the drill against each of the 2 rivets shown in the illustration, and drill off the flange of each rivet.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

      • Be careful of the drilled rivet as it may become hot.

    4. A00OIKK

      Lightly press the drill against the rivet shown in the illustration, and drill off the flange of the rivet.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

      • Be careful of the drilled rivet as it may become hot.

    5. Remove the power seat motor assembly.

    6. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.