FRONT POWER SEAT MOTOR ASSEMBLY (for Front Vertical) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Front Vertical)


    1. Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm rivet into the nose piece.

    2. A00ONGBE01
      Text in Illustration
      *1 Air Riveter

      Using the air riveter or hand riveter, install the power seat motor assembly with 2 new rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • A00OLCME11

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A00OMQVE02

        Confirm that the rivets are seated properly against the bracket.

      • Do not tilt the riveter when installing the rivet to the bracket.

      • Do not leave any space between the rivet head and bracket.

      • A00OJURE02

        Do not leave any space between the power seat motor assembly and bracket. Firmly hold together the 2 items while installing the rivet.

    3. A00ONSIE01
      Text in Illustration
      *1 Air Riveter

      Using the air riveter or hand riveter, install the power seat motor assembly with bracket with 2 new rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • A00OLCME11

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A00OMQVE02

        Confirm that the rivets are seated properly against the bracket.

      • Do not tilt the riveter when installing the rivet to the power seat motor assembly with bracket.

      • Do not leave any space between the rivet head and power seat motor assembly with bracket.

      • A00OJURE02

        Do not leave any space between the power seat motor assembly with bracket and front seat adjuster. Firmly hold together the 2 items while installing the rivet.

    4. A00OISPE01
      Text in Illustration
      *1 Air Riveter

      Using the air riveter or hand riveter, install 4 new rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • A00OLCME11

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A00OMQVE02

        Confirm that the rivets are seated properly against the front seat adjuster.

      • Do not tilt the riveter when installing the rivet to the front seat adjuster.

      • Do not leave any space between the rivet head and front seat adjuster.

      • A00OJURE02

        Do not leave any space between the motor with bracket and front seat adjuster. Firmly hold together the 2 items while installing the rivet.

    5. A00OJWA

      Using a 6 mm socket hexagon wrench, install the bolt.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
    6. A00ONCU

      Install the shield bracket with the 3 screws.

    7. Connect the connector.

  2. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A00OKFL

    2. Connect the 2 connectors.

    3. A00OKBS

      for Driver Side:

      Attach the wire harness clamp.

    4. A00OLIT

      for Front Passenger Side:

      Attach the 2 hooks to connect the connector holder.

    5. A00ONI3

      Install a new cable tie.

    6. A00OI8F

      Connect the connector.

  3. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Tech Tips


    • Use the same procedure for the RH and LH sides.

    • The procedure listed below is for the LH side.


    1. A003EE0E01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

  4. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A00ON87E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  5. INSTALL FRONT POWER SEAT SWITCH


    1. A00OM6W

      Install the front power seat switch with the 3 screws.

    2. Connect the connector.

  6. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD


    1. A00OMVA

      for Driver Side:

      Connect the connector.

    2. A00OJR5

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. A00ONUD

      Attach the 2 claws and install the 2 screws.

    5. A00OI4P

      Attach the 2 rubber bands.

  7. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A00OIGD

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  8. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A00OJR9

      Attach the 2 claws to install the reclining power seat switch knob.

  9. INSTALL FRONT SEAT ASSEMBLY

    Click here

  10. CHECK SRS WARNING LIGHT

    Click here

  11. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation Click here.

    2. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.