FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining)


    1. A00OJTX

      Remove the 2 holders together with the 2 inner reclining rods from the reclining rod.

    2. A00OLWN

      Remove the inner reclining rod and push nut from the holder.

    3. A00OL10

      Remove the inner reclining rod and push nut from the holder.

    4. A00OO07

      Install the 2 holders to the reclining rod.

    5. A00OJ0U

      Install the push nut to the holder.

      Note

      Make sure the direction of the push nut is as shown in the illustration.

    6. A00OJU2

      Install the push nut to the holder.

      Note

      Make sure the direction of the push nut is as shown in the illustration.

    7. Clean the threads of the bolt for the power seat motor assembly with non-residue solvent.

    8. Apply adhesive to the threads of the bolt for the power seat motor assembly.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    9. A00OJL9

      Temporarily install the power seat motor assembly with the bolt.

    10. A00OLGS

      Push in the inner reclining rod as shown in the illustration.

    11. A00OIN7

      Push in the inner reclining rod as shown in the illustration.

    12. A00OLZB

      Push in the 2 inner reclining rods in alternating passes to install them

      Note

      Make sure that the holder does not interfere with the power seat motor assembly or front seatback frame.

    13. Tighten the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    14. A00ONVL

      Attach the 8 hooks to install the seatback spring.

    15. A00OIWR

      for Driver Side:

      Connect the 2 connectors.

    16. A00OI7P

      for Front Passenger Side:

      Connect the connector.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. A00OMMP

      Install the separate type front seatback pad.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A00ONM4

      Attach the 2 hooks.

    2. A00OMKO

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. A00OJU0

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    4. A00ONJ0

      Pass the cable through the hole of the seatback frame.

    5. A00OJDI

      Attach the 2 claws to install the clip.

    6. A00OIX4E01
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    7. A00OI4E

      Install a new cable tie.

    8. A00OKGKE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks and close the seatback mat.

    9. Using hog ring pliers, install a new hog ring.

    10. A00OLW6

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    11. A00OJ98

      Attach the 2 claws to install the active headrest lower unit.

    12. A00OMWJE01
      Text in Illustration
      *1 Cable End
      A00OJPS Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    13. A00OIBR

      Attach the 7 hooks to install the actuator shield.

    14. A00OL1YE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    15. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    16. A00OIU0E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    17. A00OIFV

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    18. A00OMX4

      Attach the 2 hooks to connect the 2 straps.

    19. A00OILD

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    20. Attach the 2 hooks.

      A00OHZ0

  4. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A00ON87E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  5. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. A00OMVA

      for Driver Side:

      Connect the connector.

    2. A00OJR5

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. A00ONUD

      Attach the 2 claws and install the 2 screws.

    5. A00OI4P

      Attach the 2 rubber bands.

  6. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A00OIGD

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  7. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A00OJR9

      Attach the 2 claws to install the reclining power seat switch knob.

  8. INSTALL FRONT SEAT ASSEMBLY

    Click here

  9. CHECK SRS WARNING LIGHT

    Click here

  10. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation Click here.

    2. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.