FRONT SEAT SIDE AIRBAG ASSEMBLY INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH


    1. Install front seat airbag assembly LH with 2 new nuts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    2. Attach the 4 harness clamps and connect the connector clamp.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK PAD (for Manual Seat)

    A00OUAB

    1. Install the separate type front seatback pad.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK PAD (for Power Seat)

    A00OJ83

    1. Install the separate type front seatback pad.

  4. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for Manual Seat)


    1. A00OU67

      Attach the 2 hooks.

    2. A00OU1V

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. A00OS92

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    4. A00OS4B

      Pass the cable through the hole of the seatback frame.

    5. A00OUDV

      Attach the 2 claws to install the clip.

    6. A00OR0OE01
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    7. A00OTVM

      Install a new cable tie.

    8. A00OULRE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks to close the seatback mat.

    9. A00OUU1

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    10. Using hog ring pliers, install a new hog ring.

    11. A00OU7N

      Attach the 2 claws to install the active headrest lower unit.

    12. A00OS77E01
      Text in Illustration
      *1 Cable End
      A00OV9Z Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    13. A00OVHM

      Attach the 7 hooks to install the actuator shield.

    14. A00OVKNE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    15. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    16. A00OSOGE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    17. A00OSRY

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    18. A00OUJ0

      Attach the 2 hooks to connect the 2 straps.

    19. A00OU2U

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    20. Attach the 2 hooks.

      A00OVXG

  5. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for Power Seat)


    1. A00ONM4

      Attach the 2 hooks.

    2. A00OMKO

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. A00OJU0

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    4. A00ONJ0

      Pass the cable through the hole of the seatback frame.

    5. A00OJDI

      Attach the 2 claws to install the clip.

    6. A00OIX4E01
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    7. A00OI4E

      Install a new cable tie.

    8. A00OKGKE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks and close the seatback mat.

    9. Using hog ring pliers, install a new hog ring.

    10. A00OLW6

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    11. A00OJ98

      Attach the 2 claws to install the active headrest lower unit.

    12. A00OMWJE01
      Text in Illustration
      *1 Cable End
      A00OJPS Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    13. A00OIBR

      Attach the 7 hooks to install the actuator shield.

    14. A00OL1YE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    15. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    16. A00OIU0E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    17. A00OIFV

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    18. A00OMX4

      Attach the 2 hooks to connect the 2 straps.

    19. A00OILD

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    20. Attach the 2 hooks.

      A00OHZ0

  6. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A00ORGDE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  7. INSTALL FRONT SEAT CUSHION SHIELD LH (for Manual Seat)


    1. A00OV7P

      w/ Lumbar Support:

      Connect the connector.

    2. A00OU31

      Attach the claw and hook to install the front seat cushion shield LH.

    3. Install the 2 screws.

    4. A00OUW4

      Attach the 2 rubber bands.

  8. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH (for Power Seat)


    1. A00OMVA

      for Driver Side:

      Connect the connector.

    2. A00OJR5

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. A00ONUD

      Attach the 2 claws and install the 2 screws.

    5. A00OI4P

      Attach the 2 rubber bands.

  9. INSTALL SLIDE & VERTICAL POWER SEAT SWITCH KNOB (for Power Seat)


    1. A00OIGD

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  10. INSTALL RECLINING POWER SEAT SWITCH KNOB (for Power Seat)


    1. A00OJR9

      Attach the 2 claws to install the reclining power seat switch knob.

  11. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)


    1. A00OTKH

      Attach the claw to install the reclining adjuster release handle LH.

  12. INSTALL VERTICAL ADJUSTING HANDLE LH (for Manual Seat Driver Side)


    1. A00OT5S

      Install the vertical adjusting handle LH with the 2 screws.

  13. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Manual Seat Driver Side)


    1. A00OV1V

      Attach the 3 claws to install the vertical seat adjuster knob cap.

  14. INSTALL FRONT SEAT ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here