FRONT DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A010NCT

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  4. REMOVE ASSIST GRIP COVER LH


    1. A010PJH

      Using moulding remover A, detach the 9 claws and remove the assist grip cover.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. A010OCRE01

      Using moulding remover A, detach the clip and 7 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector and remove the power window regulator master switch.

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A010QZY

      Remove the 3 screws.

    2. Remove the 10 clips and 2 claws.

    3. Disconnect the courtesy light connector.

    4. A010PEDE01
      Text in Illustration
      *1 Reference Boss

      Pull out the front door trim board in the direction indicated by the arrow in the illustration to detach the 5 claws of the front inner door glass weatherstrip and remove the reference boss together with the trim board.

    5. Remove the reference boss from the front door trim board.

    6. for Power Seat:


      1. A010P79

        Detach the wire harness.

      2. A010NEF

        Disconnect the connector.

      3. Disconnect the 2 cables from the inside handle.

    7. A010O58

      for Manual Seat:

      Disconnect the 2 cables from the inside handle.

  7. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH


    1. A010SMT

      Detach the 4 claws by pulling the weatherstrip upward in the direction indicated by the arrow in the illustration to remove the weatherstrip.

  8. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A010OZZ

      for Power Seat:

      Using a clip remover, remove the 3 clamps.

    2. A010OZV

      for Manual Seat:

      Using a clip remover, remove the 2 clamps.

    3. Disconnect the 3 connectors and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the connector to the front door window regulator assembly.

    2. for Driver Side:

      Temporarily install the master switch assembly.

    3. for Front Passenger Side:

      Temporarily install the regulator switch assembly.

    4. Connect the cable to the negative (-) battery terminal.

    5. Move the door glass until the bolts appear in the service holes.

    6. Disconnect the cable from the negative (-) battery terminal.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    7. A010RIK

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    8. A010S9F

      Remove the door glass in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

    9. for Driver Side:

      Remove the master switch assembly.

    10. for Front Passenger Side:

      Remove the regulator switch assembly.

    11. Disconnect the connector from the front door window regulator assembly.

  10. REMOVE FRONT DOOR GLASS RUN LH


    1. A010SR5

      Remove the front door glass run.

  11. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    1. A010NEQ

      Remove the screw.

    2. Remove the 3 bolts and frame.

      Note

      Be careful when removing the bolts as the frame may fall and become damaged.

  12. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    1. A010OSF

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the cover with the door lock key cylinder installed.

    3. A010N81

      Using a screwdriver, disengage the 3 claws and remove the front door outside handle cover from the cylinder.

  13. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    1. A00OJ9NE01

      Using a T30 "TORX" wrench, remove the 3 screws.

    2. Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.

    3. Remove the front door lock open rod from the front door lock assembly.

    4. Remove the door lock wiring harness seal from the front door lock assembly.

  14. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A010NXH

      Remove the front door lock remote control cable assembly.

  15. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A010QBE

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A010P1P

      Remove the front door inside locking cable assembly.