REAR VIEW MONITOR SYSTEM (for Radio and Display Type) Reverse Signal Circuit

DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.


WIRING DIAGRAM

A00OS0ZE16

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK VEHICLE SIGNAL (DISPLAY CHECK MODE)


    1. A00OSPJ

      Enter the "Function Check/Setting I" mode and select "Vehicle Signal" Click here.

    2. Check that the display changes between ON and OFF according to the shift lever position.

      OK
      Shift Lever Position Display
      R ON
      Except R OFF

      Tech Tips

      This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.


    NG

    CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


    1. A00OS3XE40
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      Disconnect the D124 radio and display receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D124-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
      D124-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V
      Result
      Result Proceed to
      OK A
      NG (for Automatic Transaxle) B
      NG (for Manual Transaxle) C

    B

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY) Click here

    A

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)


    1. Disconnect the D124 radio and display receiver assembly connector.

    2. Disconnect the B14 park/neutral position switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D124-2 (REV) - B14-2 (RL) Always Below 1 Ω
      D124-2 (REV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the D124 radio and display receiver assembly connector.

    2. Disconnect the B5 back-up light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D124-2 (REV) - B5-1 (RL) Always Below 1 Ω
      D124-2 (REV) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for EA62) A
      OK (for EA63) B
      OK (for EA65) C
      NG D

    B

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    C

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    D

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here