STEREO JACK ADAPTER ASSEMBLY REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00OSNCE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00OURCE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  5. REMOVE NO. 3 BOX PANEL (w/ Console Box Lid)


    1. Place protective tape as shown in the illustration.

      A006SZ5E02
      Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  6. REMOVE NO. 3 BOX PANEL (w/o Console Box Lid)


    1. A003B2YE02
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00OQEVE01

  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00OSPV

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00OW4UE01

  10. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A006VX0

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  11. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A006VCT

      Detach the cover.

    2. A006VV0

      Using a moulding remover B, detach the 2 claws.

    3. Detach the 6 clips and remove the console panel.

  12. REMOVE BOX BOTTOM PANEL


    1. Detach the 4 claws and remove the panel.

      A00ORVLE01

  13. REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY


    1. A00OR2O

      Detach the 2 claws and remove the stereo jack adapter.