REAR DOOR SPEAKER INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL REAR NO. 2 SPEAKER ASSEMBLY (for 11 Speakers)


    1. A00OR4KE01

      Align the speaker with the door position pins labeled A.

    2. Install the speaker with the 2 screws.

      Note

      Do not touch the cone part of the speaker.

    3. Attach the clamp.

  2. INSTALL REAR NO. 1 SPEAKER ASSEMBLY


    1. Temporarily install the speaker by attaching the claw of the speaker to the door panel.

      Note

      Do not touch the cone part of the speaker.

    2. A00OV2KE01

      Using an air riveter or hand riveter, install the speaker with 3 new rivets in the order shown in the illustration.

      Note


      • A00OT9NE12

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

        Text in Illustration
        *1 INCORRECT
        *2 CORRECT
        *3 Mandrel
        *4 Riveter
      • A00OVSGE11

        Confirm that the rivets are seated properly against the speaker.

        Text in Illustration
        *1 INCORRECT
        *2 CORRECT
        *3 Riveter

      • Do not tilt the riveter when installing the rivet to the speaker.

      • Do not leave any space between the rivet head and speaker.

      • A00ORBME11

        Do not leave any space between the speaker and door. Firmly hold together the 2 items while installing the rivet.

        Text in Illustration
        *1 INCORRECT
        *2 CORRECT
        *3 Riveter

    3. Connect the connector.

  3. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00OU2R

      Connect the 2 cables to the inside handle.

    2. for 11 Speakers:

      Connect the connector.

    3. A00OSZBE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Attach the rear door trim board with the 4 claws on the rear door inner glass weatherstrip.

    4. A00OV40

      Install the rear door trim board with the 8 clips.

    5. Install the 3 screws.

  4. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A00OVNC

      Attach the 6 claws and clip to install the rear power window regulator switch assembly with rear door armrest base panel.

  5. INSTALL DOOR ASSIST GRIP COVER LH


    1. A00ORVS

      Attach the 10 claws to install the door assist grip cover.

  6. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A00OUXU

      Attach the 3 claws to install the rear door inside handle bezel plug.

  7. INSTALL REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Install the rear door regulator inside handle plate.

  8. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. Temporarily install the rear door window regulator handle assembly and fully open the window.

    2. Install the snap ring to the rear door window regulator handle assembly.

    3. A00ORY7E02
      Text in Illustration
      *1 Front Side

      Install the rear door window regulator handle assembly as shown in the illustration.

      Standard
      Area Specified Condition
      A 2.4° to 22.4°

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.