TIRE AND WHEEL SYSTEM INSPECTION


  1. INSPECT TIRE


    1. Check the tires for wear and proper inflation pressure.

      Cold Tire Inflation Pressure
      Tire Size Vehicle Speed Front Rear
      205/60R16 92V

      Driving below 160 km/h

      (100 mph)

      250 kPa (2.5 kgf/cm2, 37 psi)

      220 kPa (2.2 kgf/cm2, 32 psi)

      Driving over 160 km/h

      (100 mph)

      280 kPa (2.8 kgf/cm2, 41 psi)

      250 kPa (2.5 kgf/cm2, 37 psi)
      215/55R17 94W

      Driving below 160 km/h

      (100 mph)

      240 kPa (2.4 kgf/cm2, 35 psi)

      230 kPa (2.3 kgf/cm2, 34 psi)

      Driving over 160 km/h

      (100 mph)

      280 kPa (2.8 kgf/cm2, 41 psi)

      270 kPa (2.7 kgf/cm2, 40 psi)

      215/55R17 94W

      (for Eco Package)

      Driving below 160 km/h

      (100 mph)

      260 kPa (2.7 kgf/cm2, 38 psi)

      240 kPa (2.4 kgf/cm2, 35 psi)

      280 kPa (2.8 kgf/cm2, 41 psi)*1

      Driving over 160 km/h

      (100 mph)

      280 kPa (2.8 kgf/cm2, 41 psi)

      270 kPa (2.7 kgf/cm2, 40 psi)
      225/45R18 95W

      Driving below 160 km/h

      (100 mph)

      270 kPa (2.7 kgf/cm2, 40 psi)

      230 kPa (2.3 kgf/cm2, 34 psi)

      Driving over 160 km/h

      (100 mph)

      310 kPa (3.1 kgf/cm2, 45 psi)

      270 kPa (2.7 kgf/cm2, 40 psi)
      T145/70D17 106M -

      420 kPa (4.2 kgf/cm2, 60 psi)

      *1: for Wagon w/ HID Headlight

    2. A010R3S

      Using a dial indicator, check the runout of the tires.

      Tire runout
      1.0 mm (0.0394 in.) or less

  2. ROTATE TIRE

    A010PRGE04
    Text in Illustration
    *A w/ Full Size Spare Tire
    *B w/o Full Size Spare Tire
    *a Front of the Vehicle
    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    Tech Tips

    Rotate the tires as shown in the illustration.

  3. INSPECT WHEEL BALANCE


    1. A010S6EE01

      for Aluminum Wheel Type:

      Check and adjust the off-the-car balance.

      Maximum imbalance after adjustment
      8.0 g (0.0176 lb.)

      Note


      • Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

      • Do not touch the sticking surface of the tape.

      • Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

        Width (A)
        25 mm (0.984 in.)

      • Push the balance weight firmly to adhere it to the position.

      • Do not reuse the balance weight.

      Tech Tips


      • The inner side balance weights should be installed by clipping them to the rim.

      • If necessary, check and adjust the on-the-car balance.

    2. A010QBH

      for Steel Wheel Type:

      Check and adjust the off-the-car balance.

      Maximum imbalance after adjustment
      8.0 g (0.0176 lb.)

      Tech Tips

      If necessary, check and adjust the on-the-car balance.

  4. INSPECT FRONT AXLE HUB BEARING

    Click here

  5. INSPECT REAR AXLE HUB BEARING

    Click here