FRONT DRIVE SHAFT ASSEMBLY REASSEMBLY


  1. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH


    1. A00E9CTE02

      Using SST and a press, press on the drive shaft bearing to the inboard joint RH and bearing case.

      SST
      09527-10011
      09710-04081

      Note

      The bearing should be installed completely.

    2. Install the bearing case snap ring to install the bearing case.

    3. A00E93W

      Using a snap ring expander, install a new drive shaft hole snap ring.

  2. INSTALL FRONT DRIVE SHAFT DUST COVER


    1. A00E83SE01
      Text in Illustration
      *1 Dust Cover
      *2 Depth

      Using SST and a press, press on a new drive shaft dust cover.

      SST
      09726-40010
      09527-10011
      Standard depth
      1.0 mm (0.0394 in.)

      Note

      Be careful not to damage the dust cover.

  3. INSTALL FRONT DRIVE SHAFT DUST COVER LH


    1. A00E892E01

      Using SST and a press, press on a new drive shaft dust cover.

      SST
      09527-10011

      Note


      • The dust cover should be installed completely.

      • Be careful not to damage the dust cover.

  4. INSTALL FRONT DRIVE SHAFT DUST COVER RH


    1. A00E99TE06

      Using SST and a press, press on a new drive shaft dust cover until the dimension from the tip of the center drive shaft to the drive shaft dust cover reaches the specification as shown in the illustration.

      SST
      09527-10011
      Standard dimension (A)
      115.5 to 116.5 mm (4.55 to 4.58 in.)

      Note


      • The dust cover should be installed completely.

      • Be careful not to damage the dust cover.

  5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT LH

    A00E99AE10
    Text in Illustration
    *1 Vinyl tape

    Tech Tips

    Before installing the boot, wrap the spline of the drive shaft with vinyl tape to prevent the boot from being damaged.


    1. Install new parts to the outboard joint shaft in the following order.


      1. No. 2 axle outboard joint boot clamp

      2. Outboard joint boot

      3. Outboard joint boot clamp

    2. Pack the outboard joint shaft and boot with grease from the boot kit.

      Standard Grease Capacity
      Engine Type Capacity
      for 1AD-FTV 152 to 162 g (5.36 to 5.71 oz.)
      for 2AD-FTV and 2AD-FHV 169 to 179 g (5.96 to 6.31 oz.)

  6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT RH

    Tech Tips

    Use the same procedures described for the LH side.

  7. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

    2. Secure the No. 2 axle outboard joint boot clamp to the boot.

    3. A00EA12E04

      Place SST onto the No. 2 axle outboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the No. 2 axle outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. A00E7AJE04

      Using SST, adjust the clearance of the clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value exceeds the specified value, retighten the clamp.

  8. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  9. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

    2. Secure the outboard joint boot clamp to the boot.

    3. A00EAOCE04

      Place SST onto the outboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. A00E9OSE03

      Using SST, adjust the clearance of the clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value exceeds the specified value, retighten the clamp.

  10. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  11. INSTALL FRONT DRIVE SHAFT DAMPER LH


    1. Install the drive shaft damper to the drive shaft.

      Note

      Make sure that the damper is on the shaft groove.

    2. A00E83JE01

      Adjust the position of the damper so that the dimension is as described below.

      Standard dimension (A)
      161 to 165 mm (6.34 to 6.49 in.)

  12. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

    2. Install a new drive shaft damper clamp to the damper.

      Note

      Be sure to install the clamp on the inboard joint side in the correct position.

    3. A00E808E01

      Place SST onto the damper clamp.

      SST
      09521-24010

    4. Tighten SST so that the damper clamp is pinched.

      Note

      Do not overtighten SST.

    5. A00E8JBE01

      Using SST, adjust the clearance of the damper clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value exceeds the specified value, retighten the clamp.

  13. INSTALL FRONT DRIVE SHAFT DAMPER RH


    1. Install the drive shaft damper to the drive shaft.

      Note

      Make sure that the damper is on the shaft groove.

    2. A00E6WRE01

      Adjust the position of the damper so that the dimension is as described below.

      Standard dimension (B)
      161 to 165 mm (6.34 to 6.49 in.)

  14. INSTALL DRIVE SHAFT DAMPER SETTING CLAMP


    1. Hold the front drive shaft in a vise between aluminum plates.

    2. Install a new drive shaft damper clamp to the damper.

      Note

      Be sure to install the clamp on the inboard joint side in the correct position.

    3. A00E808E01

      Place SST onto the damper clamp.

      SST
      09521-24010

    4. Tighten SST so that the damper clamp is pinched.

      Note

      Do not overtighten SST.

    5. A00EB1HE01

      Using SST, adjust the clearance of the damper clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value exceeds the specified value, retighten the clamp.

  15. INSTALL FRONT DRIVE INBOARD JOINT LH


    1. Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boot from being damaged.

    2. Install new parts to the inboard joint shaft in the following order.


      1. Inboard joint boot clamp

      2. Inboard joint boot

      3. No. 2 axle inboard joint boot clamp

    3. A00E81YE05
      Text in Illustration
      *1 Matchmark

      Place the beveled side of the tripod axial spline toward the outboard joint.

    4. Align the matchmarks placed before removal.

    5. Using a brass bar and hammer, tap the tripod onto the drive shaft.

      Note


      • Do not tap the rollers.

      • Be sure to install the tripod in the correct direction.

    6. Pack the inboard joint shaft and boot with grease from the boot kit.

      Standard Grease Capacity
      Engine Type Capacity
      for 1AD-FTV 170 to 190 g (6.00 to 6.70 oz.)
      for 2AD-FTV and 2AD-FHV 140 to 160 g (4.93 to 5.64 oz.)
    7. A00E9VR

      Using a snap ring expander, install a new shaft snap ring.

    8. A00E9N8E06
      Text in Illustration
      *1 Matchmark

      Align the matchmarks and install the inboard joint to the outboard joint shaft.

  16. INSTALL FRONT DRIVE INBOARD JOINT RH

    Tech Tips

    Use the same procedures described for the LH side.

  17. INSTALL FRONT AXLE INBOARD JOINT BOOT LH


    1. Install the inboard joint boot to the inboard joint.

    2. A00E6PAE01
      Text in Illustration
      *1 for LH Side
      *2 for RH Side

      Check that the 2 boots are not stretched or contracted when the drive shaft is at the standard length.

      Dimension (A)
      Engine Type Item Dimension
      1AD-FTV for LH side 549.8 mm (21.6 in.)
      for RH side 930.5 mm (36.6 in.)
      2AD-FTV and 2AD-FHV for LH side 555.2 mm (21.9 in.)
      for RH side 929.5 mm (36.6 in.)

  18. INSTALL FRONT AXLE INBOARD JOINT BOOT RH

    Tech Tips

    Use the same procedures described for the LH side.

  19. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

    2. Secure the inboard joint boot clamp to the boot.

    3. A00E7NXE15

      Place SST onto the inboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the clamp is pinched.

      Note

      Do not overtighten SST.

    5. A00E9OSE02

      Using SST, adjust the clearance of the clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value exceeds the specified value, retighten the clamp.

  20. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  21. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH


    1. A00EAY8

      Using needle-nose pliers, install the axle inboard joint boot clamp as shown in the illustration.

      Note

      Be careful not to damage the boot.

  22. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  23. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH


    1. Install a new hole snap ring.

  24. INSPECT DRIVE SHAFT


    1. A003AHI

      Check that there is no severe play in the radial direction of the outboard joint.

    2. Check that the inboard joint slides smoothly in the thrust direction.

    3. Check that there is no severe play in the radial direction of the inboard joint.

    4. Check the 2 boots for damage.

    5. A003BJ7E01
      Text in Illustration
      *1 for LH Side
      *2 for RH Side

      Check that the 2 boots are not stretched or contracted when the drive shaft is at the standard length.

      Dimension (A)
      Engine Type Item Dimension
      1AD-FTV for LH side 549.8 mm (21.6 in.)
      for RH side 930.5 mm (36.6 in.)
      2AD-FTV and 2AD-FHV for LH side 555.2 mm (21.9 in.)
      RH side 929.5 mm (36.6 in.)

      If the boots are stretched or contracted, correct them.