FRONT LOWER BALL JOINT REMOVAL


  1. REMOVE FRONT WHEEL

  2. REMOVE FRONT AXLE SHAFT NUT LH


    1. A010RJ1E01

      Using SST and a hammer, unstake the staked part of the front axle shaft nut.

      SST
      09930-00010

      Note

      Loosen the staked part of the front axle shaft nut completely, otherwise the screw of the drive shaft may be damaged.

    2. While applying the brakes, remove the front axle shaft nut.

  3. DISCONNECT FRONT SPEED SENSOR LH


    1. A010SEM

      Remove the bolt and detach the clamp, and disconnect the front speed sensor wire.

      Note

      Be sure to separate the front speed sensor from the front shock absorber with coil spring completely.

    2. A010PB3

      Remove the bolt and front speed sensor from the steering knuckle.

      Note


      • Prevent foreign matter from attaching to the sensor tip.

      • Be careful not to damage the front speed sensor.

      • Clean the installation hole and the surface of the speed sensor every time the speed sensor is removed.

  4. DISCONNECT FRONT FLEXIBLE HOSE


    1. A003AQG

      Remove the bolt and disconnect the front flexible hose.

  5. DISCONNECT TIE ROD END SUB-ASSEMBLY LH


    1. Remove the cotter pin and nut.

    2. A010PVDE02

      Install SST to the tie rod end.

      SST
      09960-20010   ( 09961-02060 )

      Note

      Make sure that the top of SST aligns with the top of the tie rod end.

    3. Using SST, separate the tie rod end from the steering knuckle.

      A010Q69E02
      SST
      09960-20010   ( 09961-02010 )

      Note

      Apply grease to the bolt threads and the tip of SST.

      Note


      • Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.

      • Install SST with the center nut so that A and B are parallel. Otherwise, the dust cover may be damaged.

      • Be sure to place the wrench on the part indicated in the illustration.

      • Do not damage the front disc brake dust cover.

      • Do not damage the ball joint dust cover.

      • Do not damage the steering knuckle.

  6. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH


    1. A010SS1

      Remove the 2 bolts and front disc brake cylinder assembly from the steering knuckle.

      Note

      Use wire or an equivalent tool to keep the brake cylinder from hanging down by the flexible hose.

  7. REMOVE FRONT DISC


    1. A010P3DE05
      Text in Illustration
      *1 Matchmark

      Remove the front disc.

      Tech Tips

      Put matchmarks on the disc and axle hub.

  8. DISCONNECT FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    1. A010R9S

      Remove the bolt and 2 nuts.

    2. Disconnect the suspension lower arm from the front lower ball joint.

  9. REMOVE FRONT AXLE ASSEMBLY LH


    1. A010NKP

      Remove the 2 bolts and 2 nuts, and disconnect the front shock absorber assembly with coil spring from the steering knuckle.

      Tech Tips

      While holding the nuts in place, loosen and remove the bolts.

    2. A010QU5E02
      Text in Illustration
      *1 Matchmark

      Put matchmarks on the drive shaft and front axle hub sub-assembly.

    3. Using a plastic-faced hammer, remove the steering axle assembly.

      Note

      Be careful not to damage the front axle outboard joint boot or the magnet rotor of the hub and bearing. Do not push out the drive shaft from the axle assembly with excessive force.

  10. REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH


    1. Secure the front axle assembly between aluminum plates in a vise.

      Note

      When using a vise, do not overtighten it.

    2. Remove the cotter pin and nut.

    3. A010GN0E04
      Text in Illustration
      *1 1 mm

      Install SST to the front lower ball joint as shown in the illustration.

      SST
      09960-20010   ( 09961-02050, 09961-02050 )

      Note

      Make sure that the clearance measurement between SST and the front axle assembly is 1 mm (0.03937 in.).

    4. A010HHDE07
      Text in Illustration
      *1 Turn

      Using SST, remove the front lower ball joint from the front axle assembly as shown in the illustration.

      SST
      09960-20010   ( 09961-02010, 09961-02050, 09961-02050 )

      Note


      • Install SST so that A and B are parallel.

      • Be sure to turn the part indicated in the illustration with a wrench.

      • Do not damage the front lower ball joint dust cover.