TRANSMISSION CONTROL CABLE REMOVAL


  1. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. Remove the front exhaust pipe assembly Click here.

  2. REMOVE RADIATOR SUPPORT OPENING COVER


    1. A00OVQR

      Remove the 7 clips and radiator support opening cover.

  3. REMOVE NO. 1 ENGINE COVER


    1. A00ORGX

      Hold the rear of the cover and slowly raise it to detach the clip on the rear of the cover. Continue to raise the cover to detach the 3 clips on the front and side of the cover and remove the cover.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the cover to break.

  4. REMOVE BATTERY CLAMP SUB-ASSEMBLY


    1. A00OQGF

      Remove the bolt and loosen the nut.

    2. Detach the hook of the battery clamp from the battery carrier, and then remove the battery clamp.

  5. REMOVE BATTERY

  6. REMOVE BATTERY TRAY

  7. REMOVE BATTERY CARRIER


    1. A00OU72

      Detach the 2 clamps and disconnect the wire harness.

    2. Remove the 4 bolts and battery carrier.

  8. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A00OTZE

      Disconnect the mass air flow meter connector.

    2. Disconnect the No. 2 ventilation hose.

    3. Disconnect the air cleaner hose.

    4. Detach the 4 clamps and remove the air cleaner cap.

  9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  10. REMOVE AIR CLEANER CASE


    1. A00OUZE

      Remove the 3 bolts and air cleaner case.

  11. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00OSNCE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  12. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00OURCE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  13. REMOVE NO. 3 BOX PANEL (w/o Console Box Lid)


    1. A003B2YE02
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

  14. REMOVE NO. 3 BOX PANEL (w/ Console Box Lid)


    1. Place protective tape as shown in the illustration.

      A006SZ5E02
      Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  15. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00OQEVE01

  16. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00OSPV

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  17. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00OW4UE01

  18. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A006VX0

      Twist the shift lever knob in the direction indicated by the arrow and remove it.

  19. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A006VCT

      Detach the cover.

    2. A006VV0

      Using a moulding remover B, detach the 2 claws.

    3. Detach the 6 clips and remove the console panel.

  20. REMOVE REAR CONSOLE BOX CUP HOLDER (w/ Console Box Lid)


    1. Remove the cup holder.

  21. REMOVE CONSOLE BOX CARPET (w/ Console Box Lid)


    1. Remove the 2 carpets.

  22. REMOVE CONSOLE BOX CARPET (w/o Console Box Lid)


    1. Remove the 3 carpets.

  23. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)


    1. for Manual Transaxle:

      Remove the 2 screws.

    2. for Automatic Transaxle

      Remove the 4 screws.

    3. w/ Power Outlet Socket:

      Disconnect the connectors.

    4. Remove the 4 bolts and console box.

      A006WFRE04

  24. REMOVE CONSOLE BOX ASSEMBLY (w/o Console Box Lid)


    1. w/ Power Outlet Socket:


      1. Disconnect the connectors.

    2. Remove the 2 screws.

    3. Remove the 4 bolts and console box.

      A003DYOE01

  25. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

    A003CUE

    1. Remove the 3 nuts and front No. 1 floor heat insulator.

  26. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A003CCA

      Remove the 2 clips and disconnect the 2 cables from the transaxle.

    2. A003C8O

      Remove the 2 clips and disconnect the 2 cables from the control cable bracket.

    3. A003DT0

      Remove the bolt and detach the bracket of the control cable assembly.

    4. A003DSE

      Remove the 2 nuts and detach the grommet of the control cable assembly.

    5. A003BBD

      Remove the clip and disconnect the end of the select control cable.

    6. A003CLS

      Remove the clip and the end of the shift control cable.

    7. A003C4H

      Detach the claws and remove the control cable assembly.