MANUAL TRANSAXLE ASSEMBLY INSTALLATION


  1. INSTALL REAR ENGINE MOUNTING BRACKET


    1. A010PT9

      Install the rear engine mounting bracket with the 5 bolts.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

  2. INSTALL FRONT ENGINE MOUNTING BRACKET


    1. A010SIR

      Install the front engine mounting bracket with the 3 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  3. INSTALL ENGINE MOUNTING BRACKET LH


    1. A010PA7

      Install the engine mounting bracket LH with the 4 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  4. INSTALL MANUAL TRANSAXLE ASSEMBLY


    1. Align the input shaft with the clutch disc and install the transaxle to the engine.

      Note

      Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle to the engine with the contact surfaces of the engine and transaxle flat against each other.

    2. A010Q26E03

      Install the 5 bolts.

      Torque:
      Bolt A
      46 N*m  { 469 kgf*cm, 34 ft.*lbf }
      Bolt B
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

      Note

      Make sure that the dowel pins are fully engaged, and make sure that the contact surface of the transaxle fits close against the engine assembly before tightening the bolts.

  5. INSTALL STIFFENER PLATE RH


    1. A010SJB

      Install the stiffener plate RH with the 4 bolts.

      Torque:
      46 N*m  { 469 kgf*cm, 34 ft.*lbf }

  6. INSTALL STIFFENER PLATE LH


    1. A010O8E

      Install the stiffener plate LH with the 4 bolts.

      Torque:
      46 N*m  { 469 kgf*cm, 34 ft.*lbf }

  7. INSTALL OIL PAN INSULATOR


    1. A010PTX

      Install the oil pan insulator with the 2 bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  8. INSTALL ENGINE WIRE

    A010SCE

    1. Connect the neutral position switch connector and back-up light switch connector, install the 2 bolts, and attach the 3 clamps to install the engine wire to the manual transaxle.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

  9. INSTALL AIR TUBE SUPPORT


    1. A010O7A

      Install the air tube support with the 2 bolts.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

  10. INSTALL STARTER ASSEMBLY


    1. Install the starter with the 2 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

    2. Connect the starter wire with the nut and close the terminal cap.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

    3. Connect the starter connector.

  11. INSTALL NO. 1 AIR TUBE


    1. A00ORBGE04
      Text in Illustration
      *A for Manual Transaxle
      *B for Automatic Transaxle

      Loosen the hose clamp, and remove the 2 bolts and No. 1 air tube.

  12. INSTALL REAR ENGINE MOUNTING INSULATOR


    1. Install the rear engine mounting insulator with the 3 bolts and 2 nuts.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

  13. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


    1. Install the engine assembly with transaxle Click here.

  14. PERFORM CLUTCH ENGAGEMENT POINT LEARNING

    Click here