SHIFT LEVER ASSEMBLY INSTALLATION


  1. INSTALL FLOOR SHIFT LEVER ASSEMBLY


    1. A003DED

      Attach the 2 claws to connect the shift control cable and select control cable to the shift lever assembly.

    2. A003CLS

      Connect the end of the shift control cable to the shift lever assembly and install the clip.

    3. A003C7D

      Install the shift lever assembly with the 4 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
    4. A003BWK

      Attach the 3 wire harness clamps.

    5. Release the lock of the cable length adjustment structure of the select cable.


      1. A003E59E01

        Twist the stopper.

      2. A003CDNE01

        Pull the lock piece outward from the case to release the lock.

    6. A003CN9E01

      Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.315 in.) below the N position).

    7. A003BBD

      Connect the end of the select control cable to the shift lever assembly and install the clip.

      Note


      • Make sure the lock piece of the select control cable is facing upward when the select control cable is connected.

      • Make sure the clip is inserted in the direction shown in the illustration.

    8. A003C3PE01
      Text in Illustration
      *1 Slider
      *2 Inhibitor Wall

      Push the slider against the inhibitor wall.

      Note


      • Do not pull up the slider.

      • When adjusting the cable, make sure that the shift lever is not in 1 or 2.

    9. Lock the cable length adjustment structure of the select cable.


      1. A003APME01

        Push the lock piece into the case with slider held against the inhibitor wall.

      2. A003AVIE01

        Return the stopper to prevent the lock from being released.

        Note


        • Push in the lock piece completely.

        • Make sure that the cable length adjustment structure is locked securely.

    10. A003CN9E02

      Release the pin that fixes the transmission outer lever.


      1. Pull the pin toward the left front side of the vehicle.

  2. INSTALL CONSOLE BOX ASSEMBLY (w/o Console Box Lid)


    1. Install the console box with the 2 screws.

    2. w/ Power Outlet Socket:


      1. Connect the connectors.

    3. Install the 4 bolts.

      A003DYOE01

  3. INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)


    1. for Manual Transaxle:

      Install the console box with the 2 screws.

    2. for Automatic Transaxle

      Install the console box with the 4 screws.

    3. w/ Power Outlet Socket:


      1. Connect the connectors.

    4. Install the 4 bolts.

      A006WFRE04

  4. INSTALL CONSOLE BOX CARPET (w/o Console Box Lid)


    1. Install the 3 carpets.

  5. INSTALL CONSOLE BOX CARPET (w/ Console Box Lid)


    1. Install the 2 carpets.

  6. INSTALL REAR CONSOLE BOX CUP HOLDER (w/ Console Box Lid)


    1. Install the cup holder.

  7. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A006UDU

      Attach the 2 claws and 6 clips to install the console panel.

    2. A006VCT

      Attach the cover to the shaft.

  8. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A006TK8

      Install the shift lever knob and twist it in the direction indicated by the arrow.

  9. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Attach the 4 clips and 5 claws to install the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Connect the connector.

      2. Attach the 4 clips and 5 claws to install the panel end.

        A00E8WSE01

  10. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00E70T

      Attach the 4 clips and 5 claws to install the panel end.

  11. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. Attach the 4 clips and 5 claws to install the panel end.

      A00E7Y2E01

  12. INSTALL NO. 3 BOX PANEL (w/ Console Box Lid)


    1. When replacing the No. 3 box panel with a new one:


      1. A006V0HE01
        Text in Illustration
        *1 Cut

        Cut off the rib (the piece used to maintain the shape of the panel) shown in the illustration.

    2. Attach the 6 clips to install the box panel.

      A006X7WE02

  13. INSTALL NO. 3 BOX PANEL (w/o Console Box Lid)


    1. When replacing the No. 3 box panel with a new one:


      1. A003DNZE01
        Text in Illustration
        *1 Cut

        Cut off the rib (the piece used to maintain the shape of the panel) shown in the illustration.

    2. A003AMQ

      Attach the 6 clips to install the box panel.

  14. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00EANQE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.

  15. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00E9NPE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.